Quantcast
Jump to content


2014 volunteer just went dead

Bebop86

By Bebop86
in Cub Cadet UTV SxS Forum

 Share

Recommended Posts

Bebop86 Apprentice

Bebop86

Posted
Posted

guys- machine ran fine - Pushed button to put in 4 wheel drive and the machine died- I have power at battery and to the fuses but everything is dead-- PLEASE let em know of any ideas- I really do not know what else to look for- thanks

Bebop86 Apprentice

Bebop86

Posted
  • Author
Posted

Come on guys someone must have an idea-= Checked again and I have no power coming to wiring harness ignition switch- anyone know where the safety switches are located= really not sure where to look anymore please help--

kenfain Experienced

kenfain

Posted
Posted

Sounds like a dead short in that swith, or somewhere in that circuit. Probably blew a main fuse. You said you've got power TO the fuses. What about after? Limbs, and rocks, and other road debris is often the culprit here. Check the switch with a continuity tester. Then look around underneath where the wires go into the front drive. Or the transaxle or whatever it has. 

It's possible that it's something else, but since it happened when you hit the button. That's where I'd start looking. If it's a push button activated 4wd. There's a relay that'll drive the actuator. Both those are prime suspects.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CSM_Retired
      Making Kioti K9 2400 Quieter Ideas
      By CSM_Retired
      Greetings All,
      I'm looking for the most effective way to quiet the noise inside the cab. The cab virtually sits atop the 24hp diesel engine. It's very loud and so I'm looking for ways to make inside the cab quieter.
       
    • Gorj
      Sector E1 Battery change out
      By Gorj
      I am going to replace the batteries in my E1. I am not interested in the high cost Lithium or the expensive 6 volt dry batteries.  I am considering four 12 volt deep charge marine batteries. I have a source for 810 amp units for about $100 each.  I have no worries about reprograming the charger because it went out a few years ago and I replaced it with generic golf cart charger. When I decide to do this, I'll keep you posted on the results.
    • Marie
      2013 Hisun 800 Please Help Wiring
      By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.
    • FTG-05
      Want a new work UTV; who and what should I look for?
      By FTG-05
      I want to ditch my Kubota RTV-XG850 and its moronic twitchy throttle design flaw, get rid of the problematic engine and the 40 mph purposely throttled speed.
      So far, I'm looking at the Honda Pioneer 1000 and the Polaris Ranger 1000, both of which have 1000-1500 lb payload bed capacity.
      What other makes and models should I be looking at?
       
      Thanks for the help!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...