Quantcast
Jump to content


Recommended Posts

Posted

Hi All

Just installed a predator 670 on my Landmaster. My question is can I remove the low oil pressure wire fitting and plumb my mechanical gauge into that access point?

Thanks in advance for your advice !!

Jim

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By bms stallion owner
      hello, my BMS Stallion 600 is having accleration issues. the manual fails to show final gear oil diagrams very well... I have the owners manual and suspect issue is associated to transmission , I want to check the level of the gearoil. I located a drain plug (but not the fill plug nor dipstick). It will run - but wont exceede 2mph. Troubleshooting suggestions or comprehensive manual suggestions? Thanks
    • By Bloodhound
      Don't know the size anyone know the reliability fo theae
    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Greg Kilgore
      I would really like to know what you guys think about this. I'll try not to ramble and make it as clear as I can.
       
      I took this new job with companyX as a fiber splicer a year ago. I have a 45' bucket truck and 10or12 x 8 ft enclosed splice trailer I have to take home. Within the last 6 months all the management in the splice dept left. Now the power/construction management and higher ups are filling in. Just recently we were told travel to our 1st job is not payable even though we are in a company vehicle. 
      We are union so I asked the union business manager about this. His reply was be grateful you were paid travel as long as you were and that you don't have to drive your POV to the job.
       
      Last week I had 50hr total. The job area is 4-4.5 hrs away. My time was reduced to 44.5 hrs since we were told this travel thing on Tuesday of that week. I wasn't hired for this area. I was hired for area a lot closer to home. 
       
      Pay is good. Work is not hard. Insurance is through the union and so far pretty good.
      But I hate the thought of having to work extra just to make a 40hr paycheck. Anyone who has to drive as part of their job knows windshield time is not easy.
       
      Anyway what do you guys think. Should I look for a different job or just suck it up because of the decent pay and health insurance.
    • By Chucky 1
      I purchased a new 2023 Landmaster UTV L4 in October of 2023.  UTV didn't seem to have as much power of the demo L4 that I drove but figured once it broke in it would be better.  After about a week the unit started bogging down backfiring and stopping.  Gas fumes really bad, wait a few minutes and it would start up again.  Brought it back to the dealer and after keeping it for a few weeks said he couldn't find anything wrong with it.  Got it back home and it started acting up again, brought it back to dealer a week later and he said he found couple things that might cause it to do run bad and he was able to replicate the issue but didn't really know what was wrong.  Got it back home again after being at dealer for several weeks and the unit started running bad again right away.  Brought it back to dealer and he went back and forth with Kohler about possible fixes but just checked somethings and try to swap a few parts but still runs bad.  I called Landmaster HQ to speak with someone about a refund and was told that was handled at the dealer level.  Dealer called Landmaster and they told him they didn't do refunds or exchanges especially with units that had problems.  The dealer is now trying to get a new engine to but I have not heard anything as of yet.  I did file complaint with Better Business Bureau and they accepted my claim and reached out to Landmaster.  The National Service Manager called me and said the he had been contacted by the BBB about the complaint and he would look into it.  I told him that I would just like to have my down payment of $2,000.00 returned and never mind the over $1,000.00 I have paid in notes for a UTV that I cannot even ride on without hoping it gets me around the neighborhood.  I have found out that the 2024 Landmaster UTVs will have Vanguard engines due to issues with the Kohler engines.  Very disappointed in what is "Proudly Made in the USA" and the way Landmaster has treated this disabled veteran! 
×
×
  • Create New...