Quantcast
Jump to content


Recommended Posts

Posted

Neighbor rode their Coleman with the park brake apparently not fully released. Needless to say, things got pretty hot and even started smoking and the smoke was definitely gear oil smell. Looks like oil is coming from the area just behind the disc for the park break. Looking at parts diagram, there is an oring behind the nut/washer that attaches the flange to pinion shaft. I'm not finding anything on YT that would help with disassembly. Anyone have some experience with removing rear driveshaft ?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Prepper
      I have been doing a little research on which engine oil is best for UTV engines.  There seems to be some disagreement over using a good quality regular engine oil, and the necessity of using "M2" (or wet clutch suitable) oil.  My understanding is the "wet clutch" suitable oil has less friction reduction properties (hence a more responsive clutch with less slippage).  While less friction reduction properties would seem to be better for the wet clutch... it would not be best for the internal engine parts like camshaft bearings and other moving parts where friction is detrimental and would lead to premature failure.  Some folks swear you need M2 oil, while others say they have been using regular motor oil for years and their clutch is just fine.  Could they both be right ???
      Any thoughts ?
       
    • By Joe Breaux
      Decided to do an oil change on the Massimo ...drained oil, screen was very clean even tho oil wasn't.  Then went to remove old filter.. holy crap ..I tried every tool I have, could not budge it..Went to store and got one of the end cap type..fit nice and tight, put a 1/2 in drive ratchet on it..nope..not moving.  Put a 18 on breaker bar o. It. The inside of the removal tool broke off!!  Had to weld it back together. Put a pipe on the bar for more leverage.  Finally broke it loose..
      I have never seen a filter in my 55 yrs of working on engines so tight..And i was the one who put it on 2 yrs ago.  JUST HAND TIGHT!
       
    • By amiracle40995
      I’m getting a 700-7 every startup. I’m having to change the plug every 100 miles on 93 octane gas. I got a lower numbered plug that is supposed to burn hotter. I’m wondering why that comes up every time I start it and if it’s related? I included a picture of the code or whatever it is. I haven’t seen the code in the owners manual or the hisun shop manual I have. 

    • By Chile
      2018 Massimo 700 MSU. The machine started burning oil all of a sudden. One day fine-- next morning burning oil. Looking for advice. Do I pull the engine to inspect the top end or can it be done with the engine in place? Pro? Cons?
      Any and all assistance is greatly appreciated in advance.
      Chile
       
    • By SkyPilot56
      working on a coleman 550 out fitter , had a shit load of codes, coil, injector , and the map sensor for fuel injector replaced all 3 and figured it would start , but no joy have spark (new plug also and inline fuel filter) cleared the codes and still have the engine light , turns over fine but damn thing still will not start, friends daughters were driving it and turned it off to park , and went back to start it and same thing turns over but will not start , with this machine anyone have any ideas as to what the hell , I should be looking for , no plug's unplug checked wires none seem to be pulled apart or broken !
×
×
  • Create New...