Quantcast
Jump to content


Recommended Posts

Posted

which model HiSun do you have?

The following may or may not work 

I've done this before:

Cut off the plugs (should be male and female) of The utvs connector, and strip the wire, install crimp connectors. Do the same for the Light connector.

I usually use this type, https://www.amazon.com/Nilight-GO-05-Terminals-Connectors-Circuit/dp/B00SUTYYS2/ref=mp_s_a_1_5?keywords=quick+connectors+electrical&qid=1572137472&sprefix=quick+connectors&sr=8-5

 

any hardware store should have them.

Posted

I have the Sector 750. I guess my problem is I don’t know which wires lead to this switch? I pulled the switch and it’s fully wired into the wiring harness but where  it leads to I havn’t figured out. There is one  plug dangling under  the plastic near the fuse box  with a double wire going to it..

  • 2 years later...
Posted (edited)

On my 2021 750 EPS there (4) #16awg  Wires on the back of the "ACCT" Switch from Top to Bottom as if viewed from the windshield looking the vehicle. They are (top to bottom:

Or/Rd - 12vdc from Fuse 15 panel under front hood/cowling

Yel/Red - switched (above 12vdc) to Rear Driver Side Gray Plug

Blue/Brn - 12vdc from Fuse 15 panel under front hood/cowling

Red/Brn - switched (above 12vdc) Passenger Side Fender Well Gray Plug 

 

In my case I used the switched  red/Brn to trigger a Relay to Drive a 52in Curved Light Bar. I plan on using the Rear ACCY Plug to drive (2) work lights over the Bed pointing to rear.  For those looking for the "elusive" Gray Plug it looks like the photo...EXCEPT there is a water proof pug blanking it off.  Mine was Black

20220326_103412.thumb.jpg.368106b8004a99febcf718f8c7a08dd3.jpg

 

 

20220326_103417.jpg

Edited by 1911rocks
spelling
  • Like 1
  • Alex changed the title to Hisun Sector 750 Accessory switch

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
    • By Texjpr
      2002 ranger 500 4x4 stopped running and wouldn't restart. Service manual wiring diagram helped identify the hub safety switch as the culprit. Using jumper wires to bypass  switch allowed the engine to start and run normally. Inspection of switch showed melted epoxy and a strong smell of burnt electrical. Unable to find replacement part either used or new. Is there a work around other than jumper wiring?
    • By Paul in Wisconsin
      I have a 2023 Tracker 800SX LE that I want to add a sway bar to.
      The service manual shows how to remove and reinstall the sway bar.
      I called Cabela's to try and get the saw bar.   They said they can't get one and the 800SX doesn't have one!!??  Then why is it listed in the service manual?? No answer from them.
      Have any of you found a saw bar that fits and what did it cost?
    • By Lawrence
      Massimo coolant light blinking what does that mean?
×
×
  • Create New...