Quantcast
Jump to content


2013 Hisun 800 Wiring Help

justingrider

By justingrider
in Hisun UTV SxS Forum

 Share

Recommended Posts

justingrider Rookie

justingrider

Posted
Posted

Good morning everyone, appreciate any help on this.  I picked up a 2013 Hisun 800 for a project.  Previous owner had fried a lot of the electrical with a bunch of aftermarket audio equipment, so I have been replacing all of the wiring to give it a fresh start.  I'm 95% there with a couple of plugs I can't figure out where they need to be routed and the reason for me reaching out for help here.

1.  A female 2-port white plug that comes off the end of the main harness, close to the side where the terminal hook ups tap into the battery.  It has a Blue/black-stripe wire and a White/blue-stripe wire. (Pictures: https://ibb.co/m9PRDqX and
https://ibb.co/9pHZsFj). I'm assuming it is another single offset fuse or module like the other pieces around it but can't find anything on what it might be or that wire color combination in the manual/wiring diagrams...anyone know what this guy goes to?

2.  On the crank position sensor (torque sensor), the wires that I have coming off of that are a green wire and blue/light-gray-stripe wire (https://ibb.co/FmJLJfs)...any idea on where this guy is suppose to plug in to?

Again, thanks for any help you can provide!

-Justin

 

IMG_20191111_071958.jpg

IMG_20191110_181254.jpg

IMG_20191110_203453.jpg

  • 2 months later...
  • 5 months later...
Steve Varao Rookie

Steve Varao

Posted
Posted

Are you still trying to figure out the wiring?  I have a 800 as well and am trying to trouble shoot a no spark problem.  Let me know, the harness on my car is all connected except one mistrey plug.  Maybe we can shoot some pics back and forth and help each other out.

justingrider Rookie

justingrider

Posted
  • Author
Posted

Hey Steve, I did end up getting everything running.  Turned out my no spark issue was due to the voltage being too low from a replacement battery.  After getting a different battery it all started firing.  

Glad to share some images back and forth to help troubleshoot once I get back to the house this weekend.  

Steve Varao Rookie

Steve Varao

Posted
Posted

I got some pics for you to take a look at.  The pics are taken from the front driver side.  It took the pics from far to close, if you look close there is a with pigtail coming off the ECU harness on the right and if you look at the engine you will see a black sensor with nothing plugged in, i cannot find a plug for either of the two.   Any help would be awesome!!!  Thanks Man.

20200703_163651.jpg

20200703_163725.jpg

20200703_163716.jpg

20200703_163714.jpg

20200703_163720.jpg

  • 1 month later...
Steve Varao Rookie

Steve Varao

Posted
Posted

Hi,

Yeah im still trying to figure out the problem.  If you look in the last 3 pics i posted i did figure out that the connector just hanging there is a diagnostic plug.  In the very last pick there is a pic of what i figured out was the oil pressure sensor.  I cannot figure out where the harness connector is for it though.  Can you maybe send me a pic of it?  Also i have been going in circles trying to figure out why im not getting any spark, so far i have replaced both coils, the crank position sensor and the computer.  Ive checked continuity on the position sensor, the coil is getting power, everything is all checking out.  I even removed the stator to look at the metal blocks the crank sensor interacts with.  Im super lost right now, maybe that oil pressure sensor has to be connected in order for the engine to produce spare.  Any help would be appreciated.  Thanks

  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Homeowner A
      Diagnostic Trouble Code Help?
      By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • Marie
      Wiring 2013 Hisun 800
      By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
    • Marie
      2013 Hisun 800 Please Help Wiring
      By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...