Quantcast
Jump to content


2017 Coleman/Hisun UTV 500 axle nut socket

buck987si

By buck987si
in Coleman UTV SxS Forum

 Share

Recommended Posts

buck987si Newbie

buck987si

Posted
Posted

I'm out of town and away from our 2017 Coleman/Hisun UTV 500 Side x Side, my Son needs to replace a broken cotter pin on the front left axle and tighten everything back up.

We were able to find the cotter pin size 2.5mm x 30mm or equivalent 1/8" x 2" and I picked up a few.

I just can not find the size socket it will need and the torque setting for the axle nut.

Thanks for your time!

Greg

Travis Grand Master

Travis

Posted
Posted

Most likely it's a 22 MM nut....hisun specifies a 94 foot pounds for a 22 mm nut. If it's not 22MM take the nut to a local hardware or parts store and try to find a socket, any good parts store  ought to have individual sockets for sale.

On my mules rear axle it's a 26 MM with 110 ft lbs. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CSM_Retired
      Kioti UTV SxS Forum
      By CSM_Retired
      This is for all of you Kioti Off-Road UTV, SxS (Side by Side) owners. Discussions about Kioti Off-Road specific topics including the Kioti Mechron, K9, 2400, and 2440 models. 
    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Joe Breaux
      2017 Massimo MSU500 Thermostat Malfunction
      By Joe Breaux
      Got a 2017 Massimo MSU500 UTV with thermostat malfunction.. hot light comes on in 4-5 minutes but radiator is ice cold... where exactly is it?  The hose neck on the head has nothing in it.  I was told it was down by oil drain plug.. only thing I see is water pump.. Is in inside pump housing?  Cant find any exploded diagrams that show it.. how to I remove it? any help would be appreciated
    • Bobbers
      Axis 500 parts
      By Bobbers
      My wife accidentally ran the Axis 500 into a fence and tore the front end up (broke her arm too). Just wondering where the best place to get front end parts? I know she busted the knuckle but haven’t jacked it up yet. Thanks guys for any help!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...