Quantcast
Jump to content


Recommended Posts

Posted

Carolina Adventure World was host to the 1st annual MUD JAM on Saturday, November 8, 2008.  The MUD JAM, sponsored by CAN-AM and Yamaha, handed out over $5,500 in cash and trophies.

CAN-AM and Yamaha demo rigs were on hand with 2008 units for park attendees to enjoy free demo rides. Vendors and spectators enjoyed a sunny [...]

View the full article

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • By MISTERTIRE66
      Recently inherited 08 joyner renegade r4 800.. seems to be sound mechanically but I cannot find bal joints. Any pone help with other replacement part number please.
    • By LarryLarryQuiteRepairy
      Hello,
      Background: Bought a used 2012 700, added 2 small LED lights, wiring for a sprayer and changed front CV axles. 
      Had no electrical issues until recently. The old battery stopped charging so we got a new one, Rhino still wouldn't charge it.
      -Started next day, drove 15-20min, then out of nowhere the check engine light came on and temp too. 4WD started to automatically engage and disengage repeatedly. Charging display started jumping all around between 11 to 13 to 15v.
      -Relays, fuses, and battery connections seemed good.
      -Continuity on rectifier would jump btwn OL and 00.0
      -Rectifier wires from stator all read 20-21v at idle
      -Rectifier diode test had 1 bad reading. So, I replaced it with a new one (but still using original plugs) 
      Started it up, still shows no change (12.1v idle, 12.8 with some RPM)
      Also, I feel like now I maybe also smell burning plastic?
      Does anyone have experience with this problem or have a recommendation of where to go next?
    • By Ron from the Mitten
      I purchased a 2008 Qlink Rodeo 700 a few years ago.  I am from Michigan.  Anyone know of any local repair shops?  I had a dead battery, so I replaced that, started right up, ran the quad down the road, (this was last year), put it in the barn, shut it off.  then a couple weeks later, went to go start it again, and nothing.  I have power to the dash lights, horn, turn signals, wench etc, but nothing to the starter switch, and I hate electrical crap.  Battery still reads 12.x volts.
       
      Any suggestions would be amazing.  I've owned it over 2 years, and haven't run 1 tank of gas through it.  No time to screw with it, and very frustrated.  Hoping someone can offer some advice of value.
    • By alevins
      Good day all, 
      searching here but cannot find the answer,  Hisun been working fine and now reverse limiter seems to be engaging and cannot back up, cannot find a clear solution to disable the limiter. found a possible relay?  not sure which one or to cuut a wire at ecu but a picture or diagram would be helpful
      thank you for any help in advance
×
×
  • Create New...