Quantcast
Jump to content


2013 Odes Dominator 800 wiring help

Jeremiah1981

By Jeremiah1981
in ODES UTV SxS Forum

 Share

Recommended Posts

Jeremiah1981 Newbie

Jeremiah1981

Posted
Posted

Anyone have wiring diagrams for a 2013 dominator 800? I bought one at an auction that had some wires burned up.  There's a 9 pin connector that completely burned up so I'm trying to match the wires back up and they aren't the same colors on each side.  I believe it's the engine interface connector.

A wiring diagram or pics of that connector would be awesome. Any help would be appreciated.

 

  • 1 year later...
  • 6 months later...
  • 6 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • SouthernGypsy
      Help needed, Anyone recognize where this Internally Threaded Bolt belongs?
      By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • se3388
      Anyone else with a UT10X?
      By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
    • Jacob E freeman
      2018 cub cadet challenger 750 over heats no one knows why
      By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • Reynolds Rocket
      2017 Intimidator XD4 800 Check Engine
      By Reynolds Rocket
      I have a 2017 Intimidator XD4 800cc 4x4.  It will run great and then it's like it goes into safe mode and only runs on 1 cylinder.  It's not fouling out the plug when it happens.  Some times when I stop and restart it, it works fine.  First I thought it was a spark issue, then a fuel issue, but I feel like it's a short in the wiring some place. 
    • JimWil
      Bulldog BD300 (9/2013) 265cc parts
      By JimWil
      Looking for a place/website to order a  replacement bench seat and a dump bed fender from.
      Pics are the original orange when purchased and after painting with a textured bed liner type coating.
      Just looking for those two parts as mentioned above.
      JimWil

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...