Quantcast
Jump to content


Recommended Posts

Posted

Does anyone know what size lug nuts we have?  I do not have a tire iron to fit it, so I'm going to have to buy one.  Also, has anyone switched to steel rims?  I'm wondering if the factory lugs will seat down correctly on a set of ITP steel wheels.  I am swapping between street and off road tires for seasonal use.  

Posted

The Buck 400 takes a 19mm wrench.  To answer my own question, the stock conical lugs did well seating a set of ITP steel rims.  I'll throw up some pics later.  

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
    • By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • By Chucky 1
      I purchased a new 2023 Landmaster UTV L4 in October of 2023.  UTV didn't seem to have as much power of the demo L4 that I drove but figured once it broke in it would be better.  After about a week the unit started bogging down backfiring and stopping.  Gas fumes really bad, wait a few minutes and it would start up again.  Brought it back to the dealer and after keeping it for a few weeks said he couldn't find anything wrong with it.  Got it back home and it started acting up again, brought it back to dealer a week later and he said he found couple things that might cause it to do run bad and he was able to replicate the issue but didn't really know what was wrong.  Got it back home again after being at dealer for several weeks and the unit started running bad again right away.  Brought it back to dealer and he went back and forth with Kohler about possible fixes but just checked somethings and try to swap a few parts but still runs bad.  I called Landmaster HQ to speak with someone about a refund and was told that was handled at the dealer level.  Dealer called Landmaster and they told him they didn't do refunds or exchanges especially with units that had problems.  The dealer is now trying to get a new engine to but I have not heard anything as of yet.  I did file complaint with Better Business Bureau and they accepted my claim and reached out to Landmaster.  The National Service Manager called me and said the he had been contacted by the BBB about the complaint and he would look into it.  I told him that I would just like to have my down payment of $2,000.00 returned and never mind the over $1,000.00 I have paid in notes for a UTV that I cannot even ride on without hoping it gets me around the neighborhood.  I have found out that the 2024 Landmaster UTVs will have Vanguard engines due to issues with the Kohler engines.  Very disappointed in what is "Proudly Made in the USA" and the way Landmaster has treated this disabled veteran! 
×
×
  • Create New...