Quantcast
Jump to content


Recommended Posts

Posted

Just purchased a 2020 Pro DX  with Yanmar diesel. Had a 2007  3010 Trans Diesel I traded in. My problem is that the new machine is so much noisier  than my old one.

Has anyone had any luck in quieting down the noise? Sound proofing.?...changing the exhaust routing.?...the muffler? Any ideas or solutions would be appreciated.

  • Alex changed the title to 2020 Kawasaki Mule Pro DX Yanmar Diesel Too Loud
  • 3 months later...
Posted
On 5/30/2020 at 7:09 PM, silverbullett said:

Just purchased a 2020 Pro DX  with Yanmar diesel. Had a 2007  3010 Trans Diesel I traded in. My problem is that the new machine is so much noisier  than my old one.

Has anyone had any luck in quieting down the noise? Sound proofing.?...changing the exhaust routing.?...the muffler? Any ideas or solutions would be appreciated.

My diesel mule is extremely, and uncomfortably loud. But it's really loud at the intake, more so than the exhaust. Of course that intake comes through the roll bar, which is right by my ear, but still...

My solution was a rear window, and lots of insulation beneath the seat. Now the noise is re-routed. And much more tolerable. 

Mine is a typical old style s×s, so that approach probably wouldn't work on one of those new style dune buggies. My point is that you might need to look at deflecting the intake as well. 

  • 2 months later...
Posted

I ended up getting  Dynamat used for carhood insulation and installed it under the bed. Also wrapped the exhaust pipe up to the muffler

with  exhaust heat wrap.  The intake is not my problem for it is mounted low near the right rear tire in a compartment . The noise is

 tolerable now but must shut down to carryon a conversation!

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By JimG
      Recently, my unit Axis 500 (2020) will only go into reverse and neutral. I am not able to get high or low. The engine itself sounds fine and I do not have other issues on this unit. I change the engine oil but have not yet changed the gear oil.
      Before this happened I occasionally encountered issue where going from reverse to high gear, it would grind some and i had to reposition to shift into high gear. I also for last couple weeks heard a squeaking sound. I couldn't tell what it was. Was looking for a grease point I missed.
      The unit has around 70 hours and is kept in the garage.
      Anyone else encounter this type of scenario? Any suggestions on troubleshooting would be appreciated. Thanks.
    • By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • By Bjabbarw
      My 2021 Odes Dominator 800 bogs down at 25mph and won’t go over that speed. I have changed the fuel pump and it still does the same, it runs and idles fine, it has great reverse speed, but it won’t accelerate past 25mph. Any Ideas?
    • By Frank in MI
      Thanks for accepting me!
      Haven't got a side by side yet, but have been shopping.   
      Any advice welcome & I am on a limited budget, so haven't decided yet on new or used.
       
    • eManualonline.com Save 30% OFF Sitewide, Use code: XMAS30
    • By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
×
×
  • Create New...