Quantcast
Jump to content


2013 joyner trooper rubbing/ grinding somewhere in the rear differential or rear wheel

Chad Rice

By Chad Rice
in UTV General Discussion

 Share

Recommended Posts

Chad Rice Newbie

Chad Rice

Posted
Posted

HELP - my wife and i just bought a 2013 joyner trooper 1100 and we rode for 2 evenings with no problems. Went to ride last night and all of a sudden it acted like something was catching up and it didn't want to move easily. Whatever it was must've broke and now it moves with no problem but is making a rubbing/grinding noise somewhere in the backend. Could it be wheel bearing, differential, or something in cv shaft. Any info or similar experiences is appreciated. 

Dan B Community Regular

Dan B

Posted
Posted

Short answer to your question about possible issues:  Yes.

Impossible to troubleshoot from a distance.  I would look at everything from the transmission output shaft to the wheel bearings.

Neil Wilson Contributor

Neil Wilson

Posted
Posted
On 7/26/2020 at 9:16 AM, Chad Rice said:

HELP - my wife and i just bought a 2013 joyner trooper 1100 and we rode for 2 evenings with no problems. Went to ride last night and all of a sudden it acted like something was catching up and it didn't want to move easily. Whatever it was must've broke and now it moves with no problem but is making a rubbing/grinding noise somewhere in the backend. Could it be wheel bearing, differential, or something in cv shaft. Any info or similar experiences is appreciated. 

Maybe put it up on jacks and listen to where the sound is coming from.

  • 1 month later...
kenfain Experienced

kenfain

Posted
Posted
On 9/20/2020 at 6:03 AM, David Mcmillian said:

Has anyone found a replacement for Joyner Sand spider 650 cc outer cv axles ?

Welcome to the forum! For maximum exposure, and to observe forum courtesy, and tradition. You should open a new topic in the Joyner sub section. 

kenfain Experienced

kenfain

Posted
Posted
On 7/26/2020 at 11:16 AM, Chad Rice said:

HELP - my wife and i just bought a 2013 joyner trooper 1100 and we rode for 2 evenings with no problems. Went to ride last night and all of a sudden it acted like something was catching up and it didn't want to move easily. Whatever it was must've broke and now it moves with no problem but is making a rubbing/grinding noise somewhere in the backend. Could it be wheel bearing, differential, or something in cv shaft. Any info or similar experiences is appreciated. 

Any luck with this problem yet?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CYJSP2009
      Joyner parts
      By CYJSP2009
      Dear Joyner owners
      Any one who is looking for below Joyner parts please send email to casey from Leaf Asia  ( please send to [email protected] and cc to casey2leafasia.biz & [email protected])
      Currently, we have supply below parts: 
      1.  cv axles, cv rebuild kits, cv boots
      2.  Differentials and differential ring and pinion set
      3. Cables, 
      4. Brake parts
      5. Engine parts
      6. Other parts. 
      We will provide better price, close follow up ... 
      We can arrange productioni for parts that we can collect demands from customers  
      Have a good weekend
      Casey /  Leaf Asia 
      2023-11-17
       
    • Homeowner A
      Diagnostic Trouble Code Help?
      By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • Marie
      Wiring 2013 Hisun 800
      By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
    • Marie
      2013 Hisun 800 Please Help Wiring
      By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.
    • FTG-05
      Want a new work UTV; who and what should I look for?
      By FTG-05
      I want to ditch my Kubota RTV-XG850 and its moronic twitchy throttle design flaw, get rid of the problematic engine and the 40 mph purposely throttled speed.
      So far, I'm looking at the Honda Pioneer 1000 and the Polaris Ranger 1000, both of which have 1000-1500 lb payload bed capacity.
      What other makes and models should I be looking at?
       
      Thanks for the help!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...