Quantcast
Jump to content


Recommended Posts

Posted

7/23/20

Polaris Recalls Some 2020 RANGER XP 1000 and Ranger CREW XP 1000, 2019-2020 PRO XD and 2020 Bobcat Models

Polaris has determined that some 2020 RANGER XP 1000 and RANGER CREW XP 1000, 2019-2020 PRO XD 4000D, 2019 PRO XD 2000D and 2020 Bobcat UV34 and UV34XL vehicles may have been produced with a clutch component that was manufactured incorrectly. An incorrectly manufactured clutch component can cause the engine braking feature to fail, resulting in unexpected vehicle motion, posing a crash hazard.

 

Number of affected vehicles: approximately 15,000

 

Number of incidents: Polaris has received 14 reports of unexpected motion or drive clutch locking, including one report of a crash resulting in property damage.  No injuries have been reported.

 

Consumers should immediately stop using the recalled vehicles and call their dealer to schedule an inspection and if needed, a repair.

 

Polaris is notifying dealers and contacting affected registered owners by mail, and email if available.

 

More information is available on the CPSC Website.

 

To search off-road recalls by model or vehicle identification number (VIN), visit the Off-Road Safety Recalls page.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By JimG
      Recently, my unit Axis 500 (2020) will only go into reverse and neutral. I am not able to get high or low. The engine itself sounds fine and I do not have other issues on this unit. I change the engine oil but have not yet changed the gear oil.
      Before this happened I occasionally encountered issue where going from reverse to high gear, it would grind some and i had to reposition to shift into high gear. I also for last couple weeks heard a squeaking sound. I couldn't tell what it was. Was looking for a grease point I missed.
      The unit has around 70 hours and is kept in the garage.
      Anyone else encounter this type of scenario? Any suggestions on troubleshooting would be appreciated. Thanks.
    • By JDawg
      Was using the machine all day to haul wood...no issues until the end...
      When I try to start it, the dash lights come on but starter does not...seems like no power to the starter.
      It is in park, but when I put the brake on to start, it registers N.
      Won't start in neutral either...
      Tried rocking it, did not help...
      Help...
    • By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • By shawn b
      my hisun died on me while driving it started losing power then stalled. it wants to start but wont . it didn't over heat. I replaced plug,fuel filter injector, and fuel pump.put code reader on it and says no codes. have any ideas possibly sensor? Any input on what it could be would be appreciated
    • eManualonline.com Save 30% OFF Sitewide, Use code: XMAS30
    • By tskm
      in desperate need of a rear differential for my 2014 wildcat 1000. It has blown up right in the midst of the hurricane that struck us here in N/W N.C. I could really use this machine right now. No luck finding this from Artic Cat or the many numerous online vendors. Any info or resources wil be greatly appreciated !
      Tom 
×
×
  • Create New...