Quantcast
Jump to content


Hisun E1 Radio Install

Gorj

By Gorj
in Hisun UTV SxS Forum

 Share

Recommended Posts

Gorj Contributor

Gorj

Posted
Posted

Installed a radio/media player in my new Hisun Sector E1. Got a universal under dash kit from Amazon for $13, a radio/media player from Walmart for $17, and two speaker kits with grills from a friend for $10. Had some wire, connectors, and screws lying around. Mounted the radio in the plastic under dash kit. The radio is amazing for the price. It is only about two inches deep, but has Bluetooth, USB, and AM/FM radio. Mounted the speakers in the panel under the seat. Ran the wiring through the drive shaft tunnel. Installed a in-line fuse for the + wire and tapped in to the head lamp switch for the ign on wire. Tapped in to a ground wire in the wire loom behind the switches. I use this to play my tunes from a flash drive. I did not even bother to connect an antenna to it. Because the E1 is electric there is no engine noise to drown out the music!

 

E1 Radio.jpg

  • Like 1
kenfain Experienced

kenfain

Posted
Posted

Nice! If I add anything else to my electrical system. I'll have to use a power distribution box. Mine came with a positive battery terminal, that had an add on lug on it. 

Unfortunately, I've taken the lazy advantage of using it to power several things. Electrically speaking, it's not a concern. But it's very ugly.

Gorj Contributor

Gorj

Posted
  • Author
Posted

I have a 15 amp plug-in inline fuse at the battery plus terminal and a 14 gauge wire running to the front behind the dash. I use that to power the radio and an LED light strip that is in shipment presently. I will mount the switch for the LED lights in the knock on the dash behind the steering wheel. I am mounting the 12" light bar on the front bumper, just in front of the grill. Are you aware there is an empty 12v. connection in the rear under the tailgate? It is powered when the lights are on. In the wiring diagram it shows to be  for a license plate lamp. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Gorj
      Sector E1 Battery change out
      By Gorj
      I am going to replace the batteries in my E1. I am not interested in the high cost Lithium or the expensive 6 volt dry batteries.  I am considering four 12 volt deep charge marine batteries. I have a source for 810 amp units for about $100 each.  I have no worries about reprograming the charger because it went out a few years ago and I replaced it with generic golf cart charger. When I decide to do this, I'll keep you posted on the results.
    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • Marie
      Wiring 2013 Hisun 800
      By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
    • Marie
      2013 Hisun 800 Please Help Wiring
      By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...