07 trooper 1100 - appears to be detonating/falls on face at 3k rpms
-
Similar Topics
-
By Bryan g
We see a lot of the UT400 with shift problems, not going into gear, popping out of gear, grinding etc. There is a bulletin Im sure everyone has saw about adjusting shift cable. That dont always fix it. I went round n round with coleman on couple units. We are a Coleman warranty repair center"AFS Small Engine Repair " I told them shift lever does not have enough travel . No amount of cable adjustment will increase travel . I extended lever with piece on flat iron by 3/4 of inch . This gave shifter enough travel to properly engage into gear completely . Last couple units to come in for this Coleman sent me a modified shift lever, with longer travel . Problem solved! Also , heads up if you get any new unit ,,,go over and check it out, grease all zerks, check air filter for being in backwards, check wiring harnesses for rubbing on rotating parts, brake hose routing , make sure not touching exhaust . These are just few of the more common failures I see .
-
By Dennis
I have a bulldog i bought from home depot in 2013. In the last season it started refusing to shift from neutral to either forward or reverse. I changed the trans axle fluid and made sure the cables were lubricated and free. With a lot of coaxing, I can sometimes get it to shift. once I start driving it, things improve until I let it set awhile. Any suggestion on where to go from here?
-
By downseast
Hi everyone
Recently purchased a 2020 T-Boss 410 in what appears to be good condition
First time with this machine – I also have a diesel Kawasaki Mule which so far seems a better machine
It didn’t start and idle well particularly from cold when I got it and sudden take off ( now solved with new clutch parts ) was all or nothing !
I have replaced the idle valve, throttle position sensor, had the injector professionally checked ( ok) and also the pressure sensor this is a fuel injection engine, also plug and lead etc!
It still doesn’t run well and when starting I have to hold revs for a while as it wont idle but stall, thereafter its better and I have rebooted the ecu which has improved it
When I go to start it clicks as if there is a hydraulic lock and wont turn but after two or three attempts it then does turn over and start but I need to give it a bit of throttle to start – is this normal ?
Is there adjustment for the air idle valve ?
The engine seems rough and with vibration compared to other engines I have been used to but some say this is normal?
I haven’t changed the Lambda
sensor yet, anyone know how much difference this might make ( I have a new Bosch universal to fit )
I believe the T Boss was worked on by the previous owner
Any advice very much appreciated, thanks
-
By GunnersTacklebox
Hi All,
New here, but bought a 2022 Sector 750 brand new last march (old stock up here in Canada)
It's a good bike so far, but I have noticed a quirk and was wondering if anyone else has had a similar issue?
The issue I've had is if I leave the utv parked on any incline, not even a major incline, and leave it to sit for a while (day or two) it will not start properly. It will turn over and not fire until I press the gas pedal, when it will run and rev up, but if I let off the gas it will die. It will keep doing this until I either start it in gear and drive it for a bit or leave it in neutral and roll it down the hill to flatter ground. where it will have to sit for a while.
If I park it on a decline there is no issue. fuel is not low, it's occurred a couple times now.
Any thoughts on the cause of this? Dealership just says bring it in and let them take a look, at my expense of course.
-
-
By weasel
starts up you have keep rpms up for 5 minutes till it warms up then runs fine. But if it stalls wont start unless you unplug fuel pump and hold it to the floor till it starts then plug pump back in and run it till it warms up then it is fine all day.
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.