Quantcast
Jump to content


2012 Coleman HS700 (hisun) fan issues

EJR

By EJR
in Coleman UTV SxS Forum

 Share

Recommended Posts

EJR Newbie

EJR

Posted
Posted

I have a 2012 Coleman (hisun) hs700. The cooling fan quit working. I replaced the water temp sensor/ radiator fan switch located towards the bottom of the radiator. That did not cure the problem. I also put 12v directly to the fan to make sure the fan was still good. I then took the harness off the new temp sensor and shorted it to turn on the fan and nothing. Is there something else in line I should look at? I also found the sensor at the motor and jumpered through it. Still did not work.

Any suggestions? 

Thanks

T-boss 410 Experienced

T-boss 410

Posted
Posted

I am assuming that you had the key on when you jumped the thermoswitch plug. On my Massimo there is a fuse/relay box under the hood. Not sure where it would be located on your machine, but there is where you will find the fuse and/or the relay for the fan. 

Did the fan run when supplied with direct voltage?

EJR Newbie

EJR

Posted
  • Author
Posted

T-Boss

Thanks for replying. Yes I did have the key switch on when I jumped the thermostat. And the fan did run when I applied 12v. I also have a fuse box under the hood and tested all of them. 

  • Alex changed the title to 2012 Coleman HS700 (hisun) fan issues
  • 1 month later...
WoodsRaptor968 Newbie

WoodsRaptor968

Posted
Posted

Have you fixed your problem yet? I'm having the same (or similar) issue with a 2012 Bennche Bighorn 700 (Hisun 700).  Cooling fan works when voltage is directly applied. Temp switch works fine, and when jumpered there is voltage to the cooling fan plug.  As soon as I plug in the fan, the voltage is GONE.  I'd love to find a wiring diagram.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Homeowner A
      Black O2 Sensor?
      By Homeowner A
      I've been having misfire issues with my UTV 400 when it gets warm and I've thrown all kinds of parts at it so far with no permanent resolution.  Today I removed the O2 sensor and it is black on the end.  To me that means it's running rich and/or the sensor isn't working.  I replaced the sensor with a new one and will see how it goes I guess.  With EFI, I'm wondering why the sensor would be this way with low hours and mileage?  Is there a way to adjust or lean out fueling on these?  Thanks in advance.  
    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • Marie
      Wiring 2013 Hisun 800
      By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
    • Marie
      2013 Hisun 800 Please Help Wiring
      By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...