Quantcast
Jump to content


Recommended Posts

Posted

Ok so I can’t get an adapter for my two cheap code readers?

im assuming an adapter that is 4 pins and fits the plug in next to the fuse box may work. IMG_0277.thumb.jpeg.482378155c5d523a6e223d450cccaa5b.jpegBut if it can’t read the code from the Delphi based deal you described then it would be useless. I think it’s some kind of motorcycle brand based adapter like Yamaha or Harley. It’s just a cheap enough solution that I may try it before I spend 300$. Maybe you already know what you’re talking about. I sure don’t know much in this & many other areas. If I did my UTV would be running and not such a terrible disappointment 

Posted

Can someone tell me what connector plug you need to get to connect my Tiny Scan to connect it to my Hisun HS-550 Performance made for Rural King? The folks at that make and sell the Tiny Scan said it will work on the Hisun with Delphi EFI system. Hisun said the port connection should be under the bench seat although I have yet to find it. He said it is a white connector with black cap that will have to be removed to plug in the code scan tool and I think he said it was a 6 pin plug.

Posted

Not sure if this will help, as here are posts for the UT400, but lately with all the advertising on this blog, I find it hard to read anything anymore. I found the plug on mine under the seat,

Try here:

 

Posted

I just got off the phone with the company that makes the TINY SCAN 301 and the TINY SCAN TS-140 the TS-140 is the one I have he told me both come with a plug on them that will plug into the Hisun UTV  although I have heard the newer HISUN's use OBD2 if you have a UTV like my 2018 HISUN HS-550 Performance made for Rural King by HISUN Motor Company in Texas either Tiny Scan TS-140 or 301 will plug directly into the Hisun diagnostic plug which I finally found when I took the bench seat out and opened the lid over the engine compartment and looked down the driver side of the Engine and found the wire laying way down beside the engine lifted it and low and behold there was the 6 pin diagnostic plug with a plug-in cap that has to be removed to plug in the scanner and replaced to keep dirt and stuff when finished. Hope this helps someone. Oh the 301 does a lot more like connect to iPhone, Android, or PC via WIFI with it's own IP address but is a little over $300 the TS-140 reads and clears codes and only costs $169.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
    • By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.
×
×
  • Create New...