Quantcast
Jump to content


2011 Hisun HS 700 no power to fuel pump

Regretting my choices
 Share

Recommended Posts

Regretting my choices Newbie

Regretting my choices

Posted
Posted

Hello.  I purchased this unit as a "non runner" with the intent of using the frame to build a go-cart, but once I got it home it seemed way to good to part out.  The motor cranks over, and I have spark, but no fuel.  If I put a little fuel in the cylinder it fires up until that fuel is burnt, then of course it dies.  The fuel pump is not running and I have removed the plug and there is no power going to it.  I have checked the safety switch on the brake pedal and its fine, I have checked the fuses, all good, but am not sure where to go from here. The shifter is missing on the unit, but the indicator light on the dash shows its in neutral, and the e-brake indicator switch is working as well.  I am thinking of jumping power to the fuel pump next to see if it runs and if the motor will start.

What am I missing?  What can stop the fuel pump from getting power to it?

 

 

Randy Stevens Explorer

Randy Stevens

Posted
Posted
On 1/16/2021 at 4:24 PM, Regretting my choices said:

Hello.  I purchased this unit as a "non runner" with the intent of using the frame to build a go-cart, but once I got it home it seemed way to good to part out.  The motor cranks over, and I have spark, but no fuel.  If I put a little fuel in the cylinder it fires up until that fuel is burnt, then of course it dies.  The fuel pump is not running and I have removed the plug and there is no power going to it.  I have checked the safety switch on the brake pedal and its fine, I have checked the fuses, all good, but am not sure where to go from here. The shifter is missing on the unit, but the indicator light on the dash shows its in neutral, and the e-brake indicator switch is working as well.  I am thinking of jumping power to the fuel pump next to see if it runs and if the motor will start.

What am I missing?  What can stop the fuel pump from getting power to it?

 

 

Just for the sake of knowing, can you attach jump wire from positive side of battery to pump and see if it stays running?  You might have to find a hot wire when key is on to by-pass. Just a thought?????

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Gorj
      Sector E1 Battery change out
      By Gorj
      I am going to replace the batteries in my E1. I am not interested in the high cost Lithium or the expensive 6 volt dry batteries.  I am considering four 12 volt deep charge marine batteries. I have a source for 810 amp units for about $100 each.  I have no worries about reprograming the charger because it went out a few years ago and I replaced it with generic golf cart charger. When I decide to do this, I'll keep you posted on the results.
    • Grant
      Can’t figure out what part I’m missing
      By Grant
      I recently bought an axis 500 and it’s missing a box or something the plug is L shaped I’ve looked through the wiring diagrams and still can’t figure it out. The plug is located right near the battery housing 

    • Matthew Smith
      SXS No Crank at the Key and No Spark
      By Matthew Smith
      2013 Bennche Bighorn 700 EFI
       I just picked up this project that I was told would crank, but not start.  This is what I’ve figured out so far….
      I installed a new battery and get all dash lights, head lights, and brake lights on when turning the ignition on.  Fuel pump even turns on.  It does not crank with the key, but would when I jumped the starter solenoid, so I replaced it…..no change.
      Figured I’d check for spark and compression while I was dorking around.  Compression is 150 psi, but there is no spark.  Replaced the spark plug… no change.
      So, is my new starter solenoid bad?  Could it be the brake or gear position switches even though the brakes and neutral lights come on?  Not sure where to go from here.




    • D MAYNARD
      Axis 500 4x4 turns over but no spark
      By D MAYNARD
      I have an Axis 500 4x4 UTV that I was given.  It looks like an almost new machine with 39 hrs on it however it was apparently under water from the hurricane . I have no spark at the plug. I have replaced the plug, the plug wire, & the stator so far. Can anyone advise me of what i need to check and or replace to get this thing running? Any advise would be greatly appreciated. 
                                    Thank You,
                                  D Maynard 
       
    • dman66
      2018 Coleman UT400 Trans keeps popping out of forward
      By dman66
      My buddy has a ut400 that the forward gear keeps popping out of gear. She only has like 400 miles on the odometer .the shift cable has been adjusted and the shift lever has been updated / modified. All other gears are good. Is there an internal detent cam or something that wears out or shift fork that can be replaced ? Or is there some other magic that I can perform ? Looks like the engine needs to be split.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...