Quantcast
Jump to content


Recommended Posts

Posted

Probably putting this is the wrong spot, but i figured you guys would want to know how our cars weigh to other utv's. Weighed my daughters teryx today, the front axle was 640 and the back axle was 920, 1560lbs total. her teryx has a full cage. We are not that much heavier, we have a winch, light bar and bigger tires. I was a little surprized.

Posted
Probably putting this is the wrong spot, but i figured you guys would want to know how our cars weigh to other utv's. Weighed my daughters teryx today, the front axle was 640 and the back axle was 920, 1560lbs total. her teryx has a full cage. We are not that much heavier, we have a winch, light bar and bigger tires. I was a little surprized.

The Teryx has a stock weight of 1275 lbs,

The V-twin is a great little engine however and it has a lot of unleashed potential just waiting for all the mods that are available.

:rolleyes:;)

Posted
This teryx has no extras, just a full cage. I did not say anything about rhyno's but since you brought it up it runs away from them, sand or dirt, even when they have a chip. I weighed it my self, those are the weights, not something i read on a cardboard box. I actullay read your post because i thought you might of changed. Back on the not to read list.

So about 260 lbs for an after market cage? ouch. :o

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Karlibob
      I have a 2020 800 sx with about 16 hours on it.  From day one I have heard a clunking noise from the front end going over bumps.  Has anyone else experienced this?  Also this past weekend while out riding I heard a noise that sounded like the dump bed bounced three or four different times, again has anyone experienced anything like that.  Thanks, gary
    • By Jon Spruill
      Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks
    • By FTG-05
      I want to ditch my Kubota RTV-XG850 and its moronic twitchy throttle design flaw, get rid of the problematic engine and the 40 mph purposely throttled speed.
      So far, I'm looking at the Honda Pioneer 1000 and the Polaris Ranger 1000, both of which have 1000-1500 lb payload bed capacity.
      What other makes and models should I be looking at?
       
      Thanks for the help!
    • By Robbie Wyre
      I'm working on a 2005 Cub Cadet side by side and I'm trying to remove the front two axles.  I have a slide hammer puller on the inner joint and with all my strength they will not budge.   Anyone have the same issues and is there something I'm missing or a trick of some sort to pull these out?   Any suggestions please and thank you.
    • By CSM_Retired
      Anyone out there have a street legal UTV? Any idea how to get one registered for on highway use?
      Thanks in advance
×
×
  • Create New...