Quantcast
Jump to content


Textron Stampede leaking antifreeze

Greg Beachy
 Share

Recommended Posts

Greg Beachy Newbie

Greg Beachy

Posted
Posted

I have had a Bad Boy Stampede for almost two years now. I really like the machine but it seems like everytime I run it over 40 mph for more then a couple hundred yards it starts leaking antifreeze. The mechanic says it's a seal in the water pump, I've went through three water pumps now. Does anyone else have this problem?  And if so is there a fix for this? 

  • Alex changed the title to Textron Stampede leaking antifreeze
Greg Beachy Newbie

Greg Beachy

Posted
  • Author
Posted
13 hours ago, kenfain said:

After three pumps, I'd verify that the pumps are actually the problem. If so, then I'd look at the aftermarket pumps. What've you got to lose?

Ok thanks. What aftermarket pump did you go with? And how has performed for you?

 

kenfain Experienced

kenfain

Posted
Posted

At this point, any reputable aftermarket parts outlet should have what you need. Very few of them are actual OEM parts. As far as exactly which one, I don't really think it matters. As long as it's different from the one you've been using. A roll of the dice is as good as what you've been getting. The OEM one likely has some sort of casting flaw, causing it to defeat the seal integrity. Unless I'm misunderstanding the problem. 

When you're talking about water pump problems. There's really only the bearing, seal, and impeller. So when identifying your exact problem, you just give it a spin by hand. If it's a bearing problem, it'll feel gritty when turning it. If it turns smooth but leaks. Obviously it's only the replaceable seal. Seal kits are readily available for most of those models. Just make sure that it's a name brand pump, and preferably serviceable. 

Full disclosure; I don't own a Textron, I've had some experience in water pumps though.

  • 1 month later...
Rock-A-Buy Newbie

Rock-A-Buy

Posted
Posted

My Stampede started leaking at 1100 miles.  Required water pump *O* rings requiring pulled engine and $900 repair bill..  Nine hundred dry miles since.  Textron hasen't answerd  my letters about the problem.

cliffyk Rising Star

cliffyk

Posted
Posted
On 1/28/2021 at 9:45 PM, Greg Beachy said:

I have had a Bad Boy Stampede for almost two years now. I really like the machine but it seems like everytime I run it over 40 mph for more then a couple hundred yards it starts leaking antifreeze. The mechanic says it's a seal in the water pump, I've went through three water pumps now. Does anyone else have this problem?  And if so is there a fix for this? 

At the risk of sounding facetious, Find another mechanic!

 

  • 1 year later...
Stampede Newbie

Stampede

Posted
Posted

I have a 2019 Articat Stampede. The dealer replaced a leaky water pump at 400 miles. I have 900 miles on it now and it is leaking again.  My mechanic at the dealership said it’s a know problem. Any suggestions for a good fix would be appreciated 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • LauraLB
      2018 textron stampede 4
      By LauraLB
      Thanks for the add.  I'm looking for ideas for a hard cab enclosure. I sure don't like the soft sides and zippered window.
    • rev6engines
      Black Friday Starts Now At Rev 6!
      By rev6engines
      Black Friday is here, and we’re excited to give our offroad family 20% off on all parts and kits! Whether you're prepping for new trails or just fine-tuning your rig, we've got what you need to keep rolling. Now Is also a great time to upgrade your sled, winter's coming fast!
      If you have any questions or need help finding the right part, feel free to call, text, or email us. We’re here for you!
      Call or Text:
      801) 489-8697
      Email at:
      [email protected]
       
      Happy riding!!! 🤘

    • Jacob E freeman
      2018 cub cadet challenger 750 over heats no one knows why
      By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • russnropes
      Changing the Display to MPH from KPH
      By russnropes
      For the life of me I cannot find the directions on how to change the display to the standard for the USA - MPH. Not sure why Tractor Supply didn't do it before I bought it but it is what it is. Does anyone have the instructions to do this. I have the 2023 T Boss 550 just to be clear.
    • redneckred
      Gremlins in the machine
      By redneckred
      I have a 2012 Bennche Bighorn 700X.  I bought it used.  It had been sitting in a field for several years untouched.  I put a new sun gear in the shifter, new shifter linkage due to the old one having been patched, and a new battery (and of course fresh fuel).  The machine cranked and ran beautifully.  I had it over a year and then the machine quit running.  As it would not stay cranked, I narrowed the problem down to a bad IAC valve.  I replaced it and it ran as good as new/old.  Fast forward, the machine started to act like reverse wasn't catching and would not always back up when in gear.  Then forward quit.  I assumed a bad CVT belt and got one.  Started removing the bolts from the cover and (3) just turn in the housing without coming loose.  (2) are on the bottom, so very little room to do anything with them.  I tried cranking the machine again to see the belt move since I can move the cover enough to see the belt and now the machine will not crank.  It turns over fine.  It gets gas to the injector and has spark.  I can spray cleaner down her throat and she would run until it ran out.  I have replaced the IAC twice and put a new injector with no change.  I went out and put the old injector back in to see if that made any difference and, well, it did.  I tried to crank the machine and the starter is stuck trying to turn the machine over even with the key off.  I have to disconnect the battery to stop it.  Before I shoot this thing, what am I missing?  Is this an ECM problem or something else I am not seeing?  Been dealing with these Gremlins for over a month now and weeds are starting to overtake the motor due to it not moving.  I would love to get the thing running first and any ideas of getting those CVT cover bolts out would be extremely helpful.  Thanks in advance.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...