Quantcast
Jump to content


Recommended Posts

Posted

2008 Cub Cadet Volunteer won't start.   It is getting gas, is getting spark, but will not start.  Replaced plugs, and bit the bullet and replaced Engine Control Module (ECU).  Still nothing.  6 months ago replaced short block, starter, new ignition switch (all from Cub Cadet and Kohler).  Any ideas ??????

  • 1 year later...
Posted
On 1/29/2021 at 6:58 PM, TerryH said:

2008 Cub Cadet Volunteer won't start.   It is getting gas, is getting spark, but will not start.  Replaced plugs, and bit the bullet and replaced Engine Control Module (ECU).  Still nothing.  6 months ago replaced short block, starter, new ignition switch (all from Cub Cadet and Kohler).  Any ideas ??????

Did you ever figure it out? I have a 2008 having same issue, got it to start once but died and wouldn’t fire back up 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By JimG
      Recently, my unit Axis 500 (2020) will only go into reverse and neutral. I am not able to get high or low. The engine itself sounds fine and I do not have other issues on this unit. I change the engine oil but have not yet changed the gear oil.
      Before this happened I occasionally encountered issue where going from reverse to high gear, it would grind some and i had to reposition to shift into high gear. I also for last couple weeks heard a squeaking sound. I couldn't tell what it was. Was looking for a grease point I missed.
      The unit has around 70 hours and is kept in the garage.
      Anyone else encounter this type of scenario? Any suggestions on troubleshooting would be appreciated. Thanks.
    • By JDawg
      Was using the machine all day to haul wood...no issues until the end...
      When I try to start it, the dash lights come on but starter does not...seems like no power to the starter.
      It is in park, but when I put the brake on to start, it registers N.
      Won't start in neutral either...
      Tried rocking it, did not help...
      Help...
    • By vachi
      hi everyone i have this 2021 Hisun forge 250 that won't start. no spark no fuel.   when i turn the key on i dont hear the relays click or fuel pump come on. it does have power but the relay doesnt ground the pump or the ignition coil. dont know if there are any safety switches on this model or not.  it does crank and all the accessories work. i  hot wired the pump and it does work.  i found a wiring diagram but it's very hard to figure out and was hoping someone has seen this before. all fuses are good. thanks in advance. 
    • By boydog40
      my subaru gave it up, bought a new Predator 670cc
      problems is, wiring the buggy to the new motor, OEM key switch has 5 wires (red, green, yellow, black and brown)
      new motor has many more wires than the Subaru and i have no idea what goes where!!!
      finding any info on the web is almost impossible to do also
      any help will be greatly appreciated!
      thanks guys
    • eManualonline.com Save 30% OFF Sitewide, Use code: XMAS30
    • By Robby
      Hello, I have a 2013 500 utv hisun. Was running ok and cut out while parked. Bike will not start now. It turns over, but won't fire. I have no spark and no fuel. I replaced fuel pump, ignition coil, spark plug, cdi, voltage rectifier and all the fuses and relays. Could bad stater cause no fuel because I can't hear the fuel pump priming. Any info on where to start looking for problem.
×
×
  • Create New...