Quantcast
Jump to content


Recommended Posts

Posted

Do any of you out there find the Sector E1 seats  very uncomfortable? I get a sore neck after driving a short time. It seems the back is too upright.  It needs to be set back on an angle a  little. Any ideas ? 

  • 4 weeks later...
Posted

Hello, I just purchased an E1 last month and the seat situation was the first thing I had to resolve.  It was giving me pain in my lower back.  Here is what I did to resolve it.  There are four brackets that hold the seat back to the frame bar.  Take out the bottom screws and loosen the top screws about half way out.  Go to the lumber yard or Lowes and buy a 2X2 8 ft. long.  Cut the 2x2 to 50".  Now slide the 2x2 between the back seat and the frame.  Put one of the flat sides against the seat so there is not a square edge creating a pressure point against the back plastic which could cause it to crack.  Adjust the 2x2 so an equal amount sticks out both sides.  Now put the lower screws back in and tighten them until they are snug, but not to where they start to bend the bracket.  Tighten the upper screws back down snug as well.  This will give you a comfortable seat back angle.  It is now about the same as my Polaris ranger which I have been happy with.  I painted my brace black so it would not look too out of place, but that is up to you.  The only down side to this fix is it pushes the bottom of the seat back forward a couple inches so you loose some of the leg clearance which was minimal to start with.  I banged my knee a couple of times on the cup holder till I got used to it.  Hope this works for you.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • By camojay
      When we first heard the noise, we immediately stopped driving it...at first we thought it might be a linkage issue, but after further inspection looks like the sound/jolting is coming from the rear diff. Took a video below...
      Anyone know what is creating the diff to skip/jump like this? We drained the diff oil and didn't look terrible, no metal.
      Other info that may be useful:
      1400 miles on it
      Recently tightened the E brake
      P.s. never posted on this forum before, let me know if the video does not work
      20240817_133539_1.mp4    
    • By Homeowner A
      Have a Coleman UTV 400 that cranks, runs, drives well until it gets warm and is put under load.  Light throttle or full throttle it doesn't bog, but it will cut out mid throttle if you move the pedal quicker than it seems to like for example when you're getting ready to go up a hill, but if you immediately floor it, it will do just fine and not cut out.  It's random if and when it's going to do it, but is consistent in that it happens only when hot/full operating temperature.  I've replaced the injector twice, same with the spark plug and tried different heat ranges (NGK 7,8 and 8 iridium), replaced the fuel pump, adjusted the valves, checked air filter which is like new, changed the oil, replaced the fuel filter.  No check engine light.  I don't have a code reader for this.  Initially I thought it might have a head or head gasket issue as when I got it, the oil was over full, very runny like water milky and it was smoking.  I've changed the oil since then twice to clear and clean everything out, and it seems to be good.  Coolant stays the same level and so does oil with no changes in consistency or need for adding more. Had I think 7-9 miles when I got it and now has about 77.  What should I try or consider next?  
    • By GunnersTacklebox
      Hi All,
      New here, but bought a 2022 Sector 750 brand new last march (old stock up here in Canada)
      It's a good bike so far, but I have noticed a quirk and was wondering if anyone else has had a similar issue?
       
      The issue I've had is if I leave the utv parked on any incline, not even a major incline, and leave it to sit for a while (day or two) it will not start properly. It will turn over and not fire until I press the gas pedal, when it will run and rev up, but if I let off the gas it will die. It will keep doing this until I either start it in gear and drive it for a bit or leave it in neutral and roll it down the hill to flatter ground. where it will have to sit for a while. 
      If I park it on a decline there is no issue. fuel is not low, it's occurred a couple times now. 
       
      Any thoughts on the cause of this? Dealership just says bring it in and let them take a look, at my expense of course. 
    • By CRV
      Howdy new member here . My hobby's Rabbit dogs , gamefowl . I'm retired from my real job but I stay busy with the hounds and gamefowl . So to help around the farm I ran across an old 2007 CC Big Country 4x2 to haul feed , water , sprayer and my sorry a$$ .It is in pretty good shape , 781 hrs. good plastic , tires, ect. . But as anything outside and 18 years old it needs seats ! The thing I have found wrong mechically the Diff. Lock Acturtor is broken where it mounts to the bracket ( partly why Im here ) . Hoping someone here can help  ! Just my wish list but Id like to find a roll cage and a composit/plastic top for it Im thinking I'll need a donor to salvage these things from ( again partly why Im here ) .Is there another brand that uses this same actuator? If anyone reads this and has or knows of any of threse parts PLEASE HOLLER !! 
      Again Howdy brothers & sisters

×
×
  • Create New...