Quantcast
Jump to content


Compressing Front Springs 2008 Polaris Ranger 700XP

WADE GRAHAM

By WADE GRAHAM
in Polaris UTV SxS Forum

 Share

Recommended Posts

  • Alex changed the title to Compressing Front Springs 2008 Polaris Ranger 700XP
kenfain Experienced

kenfain

Posted
Posted

You should be able to use just about anything. I have an older 3010 mule, and I used big channel locks on mine. A couple of C-clamps would probably work too. So if you have a real strut compressor, you'll be okay. These springs aren't as dangerous as car springs. 

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Robbie Wyre
      2005 Cub Cadet side by side front axles
      By Robbie Wyre
      I'm working on a 2005 Cub Cadet side by side and I'm trying to remove the front two axles.  I have a slide hammer puller on the inner joint and with all my strength they will not budge.   Anyone have the same issues and is there something I'm missing or a trick of some sort to pull these out?   Any suggestions please and thank you.
    • mhill
      2008 American Sportsworks TW265 UTV - steering
      By mhill
      I purchased a 2008 American Sportsworks Subaru TW265 UTV, with no manual and no previous knowledge. When idling, the steer column shakes uncontrollably, is very noisy, and might be from vibrations from the engine. Logically, I am thinking engine vibration moving up the steering column. I found a schematic, but that has not helped in identifying the specific problem.
      Any thoughts? Suggestions?
      Thanks so much
    • staind
      Joyner R2 2008 800cc ECM code reader Lite or OBD port install
      By staind
      Looking for information on installing a OBD port or a lite to read codes in ECM. 
      I can not find a OBD port or a lite to read codes on this R2 with 800cc. 
      I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking. 
      This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
      I want to know what the ECM is reading to help dio it.
      This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever. 
      thanks Dan D. aka staind
    • Troy C
      2012 Polaris Ranger 800 Convert to EV
      By Troy C
      I am new to forum but I have a 2012 polaris ranger 800 that motor went out and had it replaced and a year later here i am again so i am interested in converting it to EV . I am 72 but pretty active and live on 500 ac of land  that part is in hills but most is in low land. I have no idea what i need or want so any advice will be appreciated. Thanks guys 
    • Brett
      2006 Polaris Ranger 700 side by side idles fine but dies when you touch the gas
      By Brett
      Fuel injected 700 starts great and idles great but touch the gas and it dies

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...