Quantcast
Jump to content


Massimo 500 wont start, Got Fuel, Dry spark plug

Lance Darbonne

By Lance Darbonne
in Massimo UTV SxS Forum

 Share

Recommended Posts

  • Alex changed the title to Massimo 500 wont start, Got Fuel, Dry spark plug
cliffyk Rising Star

cliffyk

Posted
Posted
23 minutes ago, Lance Darbonne said:

Massimo 500 wont start.  Pulled the injector and when i turn the key it sprays a lot of fuel, but the spark plug is dry.  What would be my next step?  Valve adjustment?

You need three things to run an ICE: fuel (a proper air/fuel mix), compression and a spark at the correct moment. One of those is missing. 

Easiest thing to check next (if you have not yet) is for a spark. OHC valvetrains rarely wear themselves tighter (s o tight as to not close and not allow some compression)--not what I'd check next...

 

cliffyk Rising Star

cliffyk

Posted
Posted

As I alluded to above, with an engine that was  running reasonably well before a starting problem valve adjustment would likely be the last thing I'd check--just yank the plug and test the compression. If an intake or exhaust  valve is not closing tightly the cranking compression will be rather low (likely <100 psi)...

Lance Darbonne Newbie

Lance Darbonne

Posted
  • Author
Posted

Thanks Guys, the thing that was puzzling me was that the injector was sending fuel, but the spark plug remained dry, which is why i asked about valve timing, but it does make sense what cliffyk said.

When i pulled the injector, it didn't really send a fine mist, but wasn't a solid stream, but it is sending fuel.   What would cause that fuel not to go into the cylinder?

cliffyk Rising Star

cliffyk

Posted
Posted
7 minutes ago, Lance Darbonne said:

Thanks Guys, the thing that was puzzling me was that the injector was sending fuel, but the spark plug remained dry, which is why i asked about valve timing, but it does make sense what cliffyk said.

When i pulled the injector, it didn't really send a fine mist, but wasn't a solid stream, but it is sending fuel.   What would cause that fuel not to go into the cylinder?

That is perplexing--Check the spark and compression. Is there a smell of gas in the cylinder? I have seen "no-start" EFI systems where the fuel just ran down the cylinder wall and into the crankcase--does the oil smell of gas?

  • Like 1
  • 1 month later...
Lance Darbonne Newbie

Lance Darbonne

Posted
  • Author
Posted

Guys, I want to thank you for all of your help, as well as let you know what the problem was.  I went on an out of state trip after my last post, so hadn't had time to get back on this unit until lately.  During my initial troubleshooting, i was on the drivers side working on the unit and my granpa was on the other side.  When i went back to verify the injector had a good spray pattern, i was not getting any fuel out.  I wiggled something and it started spraying again.  I leaned over to look at the fuel pump and noticed fresh oil.  Traced it to the oil filter which was barely hanging on.   

So, the whole problem was an oil filter with the wrong thread type was installed.  It screwed on, but over time, and with vibration, came loose and fouled the threads on the filter.  After it started spewing oil, i guess the low oil sensor was engaging causing the bike to dye intermittantly, until the oil was never able to reach the sensor.  I ordered a new filter, installed, and topped off the oil, and now she is running great.

The only thing i wonder is why i was getting fuel and fire with pretty much no oil?   I would figure that the sensor would kill the fuel or the fire???

  • 2 months later...
Gerals Newbie

Gerals

Posted
Posted

I have a 2017 missimo 500 I am replacing the fuel pump the replacement pump has the two lines to the Lead out ports which is ok but on the pump housing it has a open hose nipple where does it go

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Prepper
      2015 MSU-500 crank - no start
      By Prepper
      I'm working with a 2015 MSU-500.  Basic symptoms are it cranks well, but will not fire.  It has spark, and it has fuel spraying out of the injector (and spraying starting fluid into the throttle body and plug hole makes no difference).  It has compression.  I bought it not running, and no other information was available.  It has 775 miles on it and 127 hours.  It looks to be in very good shape.   Previous owner replaced fuel pump, ECU, coil, plug, and the fuse/relay box that mounts on the firewall, then gave up.
      My questions relate to cam/valve timing, considering the symptoms and diagnostics so far.  My thinking was the woodruff key sheared off and the crank spun, making it out of time.  My question is, by the pictures attached does anyone have an opinion as to the cam/valve timing being correct?  In the crankshaft picture you can see a timing mark visible.  In the camshaft picture I have arrows directed towards what I think are timing marks (which appear to be exactly 180 degrees from one another).  However, the long arrow in what appears to be bolt configuration in line with the piston/rod line.  Here is a puzzling note... in the position you see in the pictures... I have valve lash on both the intake and exhaust.  I think it's at TDC, given the visible crank timing mark and valve lash on both valves. 
      Any thoughts ?  Does this appear to be in proper valve time ?  Have I missed anything simple ?  Thanks in advance for your input.


    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Joe Breaux
      2017 Massimo MSU500 Thermostat Malfunction
      By Joe Breaux
      Got a 2017 Massimo MSU500 UTV with thermostat malfunction.. hot light comes on in 4-5 minutes but radiator is ice cold... where exactly is it?  The hose neck on the head has nothing in it.  I was told it was down by oil drain plug.. only thing I see is water pump.. Is in inside pump housing?  Cant find any exploded diagrams that show it.. how to I remove it? any help would be appreciated
    • Bobbers
      Axis 500 parts
      By Bobbers
      My wife accidentally ran the Axis 500 into a fence and tore the front end up (broke her arm too). Just wondering where the best place to get front end parts? I know she busted the knuckle but haven’t jacked it up yet. Thanks guys for any help!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...