Quantcast
Jump to content


Massimo 500 wont start, Got Fuel, Dry spark plug

Lance Darbonne

By Lance Darbonne
in Massimo UTV SxS Forum

 Share

Recommended Posts

  • Alex changed the title to Massimo 500 wont start, Got Fuel, Dry spark plug
cliffyk Rising Star

cliffyk

Posted
Posted
23 minutes ago, Lance Darbonne said:

Massimo 500 wont start.  Pulled the injector and when i turn the key it sprays a lot of fuel, but the spark plug is dry.  What would be my next step?  Valve adjustment?

You need three things to run an ICE: fuel (a proper air/fuel mix), compression and a spark at the correct moment. One of those is missing. 

Easiest thing to check next (if you have not yet) is for a spark. OHC valvetrains rarely wear themselves tighter (s o tight as to not close and not allow some compression)--not what I'd check next...

 

cliffyk Rising Star

cliffyk

Posted
Posted

As I alluded to above, with an engine that was  running reasonably well before a starting problem valve adjustment would likely be the last thing I'd check--just yank the plug and test the compression. If an intake or exhaust  valve is not closing tightly the cranking compression will be rather low (likely <100 psi)...

Lance Darbonne Newbie

Lance Darbonne

Posted
  • Author
Posted

Thanks Guys, the thing that was puzzling me was that the injector was sending fuel, but the spark plug remained dry, which is why i asked about valve timing, but it does make sense what cliffyk said.

When i pulled the injector, it didn't really send a fine mist, but wasn't a solid stream, but it is sending fuel.   What would cause that fuel not to go into the cylinder?

cliffyk Rising Star

cliffyk

Posted
Posted
7 minutes ago, Lance Darbonne said:

Thanks Guys, the thing that was puzzling me was that the injector was sending fuel, but the spark plug remained dry, which is why i asked about valve timing, but it does make sense what cliffyk said.

When i pulled the injector, it didn't really send a fine mist, but wasn't a solid stream, but it is sending fuel.   What would cause that fuel not to go into the cylinder?

That is perplexing--Check the spark and compression. Is there a smell of gas in the cylinder? I have seen "no-start" EFI systems where the fuel just ran down the cylinder wall and into the crankcase--does the oil smell of gas?

  • Like 1
  • 1 month later...
Lance Darbonne Newbie

Lance Darbonne

Posted
  • Author
Posted

Guys, I want to thank you for all of your help, as well as let you know what the problem was.  I went on an out of state trip after my last post, so hadn't had time to get back on this unit until lately.  During my initial troubleshooting, i was on the drivers side working on the unit and my granpa was on the other side.  When i went back to verify the injector had a good spray pattern, i was not getting any fuel out.  I wiggled something and it started spraying again.  I leaned over to look at the fuel pump and noticed fresh oil.  Traced it to the oil filter which was barely hanging on.   

So, the whole problem was an oil filter with the wrong thread type was installed.  It screwed on, but over time, and with vibration, came loose and fouled the threads on the filter.  After it started spewing oil, i guess the low oil sensor was engaging causing the bike to dye intermittantly, until the oil was never able to reach the sensor.  I ordered a new filter, installed, and topped off the oil, and now she is running great.

The only thing i wonder is why i was getting fuel and fire with pretty much no oil?   I would figure that the sensor would kill the fuel or the fire???

  • 2 months later...
Gerals Newbie

Gerals

Posted
Posted

I have a 2017 missimo 500 I am replacing the fuel pump the replacement pump has the two lines to the Lead out ports which is ok but on the pump housing it has a open hose nipple where does it go

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Jim Kessell
      EH65 spitting fuel from breather hose into air filter.
      By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • Nutcase
      Joyner trooper Fuel injection
      By Nutcase
      I have a Joyner Trooper 1100 4 place that has been sitting for a number of years. I have everything taken care of but i can't get the fuel through the injectors. Fuel pump puts full pressure on them but they don't turn on or spray fuel. Any ideas?
    • NC4wd
      Axis 500 Lift Kit
      By NC4wd
      Has anyone found a lift kit that fits an Axis 500? Mine is a 2021.
    • Greg Kilgore
      Heater installed 2021 Axis 500
      By Greg Kilgore
      Last year bought a small universal coolant style cab heater. Well I installed it today. Thanks to another member, RangeRider45, and his install
       
      That told in his post the size fitting he used. I got the same fittings plus a few others. And all went kinda smooth. Took a few minutes to get air purged from coolant system. Should have parked on hill with front up in the air. But would have had a hard time working on it.
      I had a variable power switch connected to an overhead cab fan. Never really used the fan that much. And I have to remove the fan to put on my cab enclosure anyway. So I repurposed the switch to supply power for the heater. The heater has 2 12-volt DC computer fans that are rated for 1.8 amps each. So it's not going to be a big drain on the weak charging system. And with the switch I've got great control over the speed of the fans.
      If anyone is interested the radiator hoses are 7/8 inch. I reworked the temperature sending unit (moved it closer to radiator) to make room for all the extra plumbing I did to get the heater to work the way I wanted. 
      Plumbing parts list.
      10-15 worm water clamps. 3/4 to 1 1/4 inch size.
      2 1" x 3/4" x 1" PEX Tee
      1 3/4" PEX ball valve
      1 1" PEX ball valve
      5/8" heater hose. I got 6' and probably have 4' left over.
      I used the radiator house I cut out to use as splices between the PEX fittings. The PEX fittings are not true to their dimensions that are stated on the package. So they fit the 5/8" and 7/8" very nicely.
      They way I have it plumbed is from radiation out side. A tee, then the 1" ball valve, then a Tee. Coming off the Tees are the hoses going to the heater core. There is a 3/4" ball valve on one of the Tees. The ball valves are used to bypass the heater core in the summer. Or direct the hot coolant through the heater core in winter. The temperature sending unit tells me how hot the coolant is. And if anything is getting too hot. The dash also has an idiot light that comes on if the head gets too hot. But doesn't do anything if the radiator gets too hot. There is a temp sensor on the radiator that controls the electrical fan. But if the coolant isn't circulating. That switch never sends a signal to turn on the fan. But enough talking/rambling. Everyone wants to see pics. The only thing I need to change is the orientation of the handle on the 1" ball valve. I have 2" or more clearance between the handle and the tire when cut hard right. But I still don't like it. And instead of taking the valve out and rotating 180°. I'm just going to take the nut off and rotate the handle 180°. Think I need to make a locking mechanism to lock the handles in place so they don't vibrate closed when the machine is moving.
      The temperature sending unit and housing. Size 22 mm. Aluminum from Amazon.

      Upper Tee the lower Tee is identical. Can also see the handle of the 3/4" ball valve on the 5/8" hose going to the heater.

      The 1" ball valve. Goes between the 2 Tees

      Wide view of the plumbing.

      The heater installed in the sxs. The 3 black hoses are just hanging there. Zip ties to the heater but not attached to any thing. Will probably just direct 2 toward the wife's feet. And 1 toward mine. Or what ever is need as the heat is needed on rides. The black hose in passenger floorboard is some 1" hose that is not needed. Don't know what I'll do with it.

       
      I think if I was going to do it again. I'd put some Indian Head gasket dressing or silicone on the 1" side of the PEX fittings. And I may still do that. But I really hate the ideal of introducing air back in the coolant system.
       
      Any questions just ask. It may take a while to answer. But I'll try.
      Ya be good and stay warm over the next few months 
       
      Kilgore.
    • Hunterman22
      2021 Hisun Axis 500 No Start - Need Help Please
      By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...