2008 Yamaha Raptor 250 Service Manual
-
Similar Topics
-
By mhill
I purchased a 2008 American Sportsworks Subaru TW265 UTV, with no manual and no previous knowledge. When idling, the steer column shakes uncontrollably, is very noisy, and might be from vibrations from the engine. Logically, I am thinking engine vibration moving up the steering column. I found a schematic, but that has not helped in identifying the specific problem.
Any thoughts? Suggestions?
Thanks so much
-
By staind
Looking for information on installing a OBD port or a lite to read codes in ECM.
I can not find a OBD port or a lite to read codes on this R2 with 800cc.
I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking.
This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
I want to know what the ECM is reading to help dio it.
This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever.
thanks Dan D. aka staind
-
By CSM_Retired
View File Kioti Daedong K9 2400 Shop Manual
This manual is to provide servicing personnel with information on the general speci- fications, service, operating principle, troubleshooting, exploded view including part name, removing and installing procedures for K9 2400/K9 2440 UTV (Utility Vehicle) with high-end technology.
All information in this manual is based on the latest product information available at the time of publication. Therefore, some of the information in this manual may differ from the machine you have.
KIOTI has a principle to apply update to the next edition of the manual if there is any. However, KIOTI has no obligation to modify the contents in this manual, especially the contents in the manual which is already distributed or published.
The modified information is available in KIOTI's online electronic manual system (DEMSS).
This manual is ultimately to satisfy customers with best performance of this UTV. If there is any typo, wrong information or question for this manual, feel free to contact KIOTI.
Submitter CSM_Retired Submitted 01/02/2025 Category KIOTI
-
By vachi
hi everyone i have this 2021 Hisun forge 250 that won't start. no spark no fuel. when i turn the key on i dont hear the relays click or fuel pump come on. it does have power but the relay doesnt ground the pump or the ignition coil. dont know if there are any safety switches on this model or not. it does crank and all the accessories work. i hot wired the pump and it does work. i found a wiring diagram but it's very hard to figure out and was hoping someone has seen this before. all fuses are good. thanks in advance.
-
-
By boydog40
my subaru gave it up, bought a new Predator 670cc
problems is, wiring the buggy to the new motor, OEM key switch has 5 wires (red, green, yellow, black and brown)
new motor has many more wires than the Subaru and i have no idea what goes where!!!
finding any info on the web is almost impossible to do also
any help will be greatly appreciated!
thanks guys
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.