Quantcast
Jump to content


2015 Hisun Forge 110 No Spark, No Injector Pulse. Please HELP! Willing to pay $100 for help assisting with a diagnosis!


Recommended Posts

Posted

I have a 2015 (EFI) Hisun Forge 110 atv that has no spark or injector pulse.  I have replaced the Stator/pickup coil and ECU and still can not get anything.  I have brought it to 3 different Hisun Service centers and no one can figure it out.  The last service center said they can get a very "weak" spark but that is about it.  I consider myself pretty knowledgeable about engines but this one has me (and 3 Hisun service centers) stumped.  I just uploaded the service manual for this machine.  Any help or advise that you can give is going to be much appreciated!

110 ATV Service Manual.pdf

  • AdamG changed the title to 2015 Hisun Forge 110 No Spark, No Injector Pulse. Please HELP! Willing to pay $100 for help assisting with a diagnosis!
Posted

I would look for a short to ground.  

Also, check coil and pick-up. I know u replaced trigger, check it anyway!

Primary coil resistance 
0.18 ~ 0.28 Ω at 20 °C (68 °F)
• Connect the multimeter(Ω × 1k) to the
ignition coil. 
Tester (+) lead Orange lead terminal
Tester (–) lead Spark plug lead
• Check that the secondary coil has the
specified resistance.
Secondary coil resistance
6.32 ~ 9.48 kΩ at 20 °C (68 °F)

Posted

. Pickup coil resistance
• Disconnect the A.C. magneto coupler from
the wire harness.
• Connect the multimeter(Ω × 100) to the
pickup coil terminal. 
Tester (+) lead Green/White terminal ①
Tester (–) lead Blue/White terminal ②
• Check the pickup coil for the specified
resistance. 
Pickup coil resistance 
459 ~ 561 Ω at 20 °C (68 °F)
(White/Red – White/Green)

Posted

If those two components pass, check resistance in spark plug cap and replace plug. Check for spark again. 

If all that is good, check fuses, main switch, wiring connections for entire ignition system.

Most importantly,  check the battery for a minimum of 12.6 volts!

9.6 volts while cranking!

Posted

Do a simple voltage test on the DELPHI ECM.....BLK connector.....as follows:

Pin 18......+12 Vdc....Always Hot...Battery

Pin 15......+12 Vdc......ONLY with ign key ON.  0 Vdc with key OFF.

Also power grounds on BLK Pin 2 and GREY Pin 9.

Posted

Thanks for the replies @Savage3 and @Ben1098.  I checked everything and the only thing out of spec is the pickup coil.  I am getting a reading of 119 OHMs when the specs say it should be 459-561.  The problem is that it is brand new.  I also tested the old one (the one that was on when it was running) and it has virtually the same resistance (116 OHMs).  AC voltage coming out of the pickup coil at cranking speeds without the spark plug in is 3.5 volts.  Not sure what it is supposed to be.  Could a bad rectifier cause a no spark/injector pulse issue?

I am at a complete loss.   I live in the Dallas, Texas area.  I would be willing to pay someone to diagnose.  

Posted

Sounds like you have a short somewhere. Difficult to help with electrical problems without performing the tests. Follow the service manual step by step. The problem will be small and most likely due to corrosion, broken wire, or bad connection. 

Make sure your battery is good, very important! They wont run in many cases due to something as simple as low voltage.

Posted

I did some testing last night and got some "weird" readings.  I tested the pickup coil from 2 different places; directly from the plug (got 119ohms) and at the end of the wiring harness that goes into the Delphi ECU.  The 2 pickup wires that go to the ECU are shielded with a grey exterior and foil looking interior (assuming for more insulation)  When I tested the resistance just before the ECU (where the pick up wire go into the ECU) I was getting anywhere from 8-10 milliOHMs.   I was assuming I should have the same resistance when checking just before the ECU but the resistance was drastically reduced.  I then tested the resistance of the shielded pick up wires and there is no resistance at all.  Not sure if this all makes sense and you are tracking with me.  I can take pics to better explain if needed.  Not sure if this is a red flag or normal.  Thoughts?

Posted

The pickup coil signal wire is shielded due to ECU input can "see" other "trash" like the starter current pulses.

You have a smashed cable which shorts signal to GND....this the mohm reading you get.  Shielded cable is toast....cut back the cable to leave two (2) pigtails.  Connect the open ends....ECM input and the pickup coil output(s).  Go to electronics store a buy a chunk of shielded cable...take sample along.....SOLD ER all 4 joints...route new wire run far away from starter HOT and the 3 PH stator to Regulator wires

Posted

@Ben1098  Thanks for the reply.  I unplugged the shielded wires from the ECM and pick up coil (completely isolated) and tested each shielded wire individually and they both have 0 resistance.  It just does not make sense why the difference in resistance when it is plugged into the pick up coil yet there is no resistance when it is unplugged.  

Posted

New or not, I don't believe that pick-up will work at 119 ohms. I've never seen one that is working less then 400 ohms. Whe you test it, is it off the machine?

Posted

It was on the ATV when I tested it.  I tested the old one (from when it was running) and it is 116 OHMS when it was off the ATV.  

Posted

Pickup coil resistance
• Disconnect the A.C. magneto coupler from
the wire harness.
• Connect the multimeter(Ω × 100) to the
pickup coil terminal. 
Tester (+) lead Green/White terminal ①
Tester (–) lead Blue/White terminal ②
• Check the pickup coil for the specified
resistance. 
Pickup coil resistance 
459 ~ 561 Ω at 20 °C (68 °F)
(White/Red – White/Green)

Posted

We can't ignore the specifications provided in the service manual

That taken into account, resistance is not the best way to test. Dynamic would be better, was the voltage in spec with new trigger when you tested it?

Posted

I have a new 200 ohm coil, I tested that with 3 meters. All three were at 153, 159, 151. 

I also put it on and cranked machine, the voltage was in spec.

So, resistance can be off a little and the coil still works. I'm not sure it can be off as much as yours.

Posted

Tried again....no answer....try [email protected]

Guessing what your question would be:

450 ohm vs 210 ohm coils.  Seen both used.  The 450 ohm had failure problems..thermal good/bad self healing.  Tech info...the output is the real object.  Internal construction better magnet and heavier wire/less turns (lower resistance) but gives equal pulse output.  Chino service manual...copy of Yamaha Rhino SxS clone copied Yam specs and NOT what was in machine.

Pickup coil.  Output is signal and signal gnd taken off BOTH ends of the coil windings.  Tech.....the pulses due to make/break of magnetic circuit are + and then - repeating as the flywheel rotates.  Coil can be wired wrong.....as in backwards....resulting in a timing error.  Most ign modules trigger off + edge.  Thus timing will be off.

Shielded wire consists of insulated signal wire(s) wrapped with a foil shield and then a bare (drain) wire wrapped around foil...all with a outer insulation jacket.  You application has a single center wire (signal) and the bare drain wire is signal gnd.  Smash the cable and the foil/bare wire will short to the inner signal conductor.  I've seen a wire tie too tight break down the insulation on well used machines.  In your case

1. Pickup R was "correct" at output at engine.

2.  Measured at Delphi ECM very low R...SHORT.....due to insulation failure in S cable.

3.  Measured R in both center and drain wires and OK.....these wires are still intact....will both be low R.

4.  The internal short will kill the weak pickup signal...ECM no timing signal....dead.

Posted

@Ben1098  Thanks again for the info.  I just did another test and I think I confirmed the shielded wire is bad.  I hooked up my DVM directly to the pick up coil out of the crank case housing and got 3.9 volts AC when cranking the engine over.  I plugged the pick up coil back to the shielded wire, cranked the motor and tested voltage at the ECU plug and got 0 voltage (no signal going into the ECU).  I am going to try and find some shielded wire and make the soldered connections as you suggested.  I will report back to let you know if that fixed the problem.  

Posted

A fast test is just use 2 jumper/clip leads.  The signal will be good enough if NOT routed against harness.  If miss fire or sputtering,  shield the signal wire.  Grab some Al foil strip 1/2" wide...wrap length wise....finger roll tight...masking tape here and there and the ends (stay off the ends...no shorts) AND take a 3rd clip lead....attach to foil and a good ground (signal gnd).  Shielded cable on the cheap.

Posted

SUCCESS!!!  Finally figured out the problem.  The plug that connects the pickup coil to the shielded wire to the ECU was bad.  Soldered the wires together and starts and runs good; under 10mph...  Lesson learned: check the voltage all the way to the ECU.

I took the ATV for its maiden voyage and it was only able to get up to 10-12 mph before cutting out.  Once under 10mph it kicks right back in.  It is not specific to the RPM's either.  Also I can fly in reverse but that is a little scary.  

Is there some sort of safety device on the ATV that limits the forward speed to 10mph?  

Posted

So I figured out why I could only go 10-12 mph in forward.  I called "Motorcycle Doctor" out of Missouri and a guy named Craig is an expert when it comes to Hisun anything.  They also sell Hisun parts.  Once I told him what was going on, he immediately said he knew exactly what the problem was.  It is the reverse rev limiter.  He said cut the wire at the ECU and it will fix it.  I explained that it was not a problem in reverse or a revving issue, it just would not go over 10 mph.  He said it did not matter, forward or reverse, for some reason Hisun ECU's do not know what gear you are in (FWD or REV) and will limit your speed in forward or reverse.  I cut the wire he told me to cut and sure enough, no more speed limiter!  It does about 30mph with me on it.  It also runs about 9,000 rpms.  I did not think they spun that fast!  I uploaded the document that Craig sent me explaining what wire to cut.  I think this is just for the machines with the 2 plug Delphi ECU's.  In the document it says that it is a blue and green wire but mine was a green and white wire.  I confirmed via the service manual that I was cutting the correct wire.  Hopefully this helps someone else who runs into the same problem.  

Reverse Rev Limit ECU.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By rev6engines
      Black Friday is here, and we’re excited to give our offroad family 20% off on all parts and kits! Whether you're prepping for new trails or just fine-tuning your rig, we've got what you need to keep rolling. Now Is also a great time to upgrade your sled, winter's coming fast!
      If you have any questions or need help finding the right part, feel free to call, text, or email us. We’re here for you!
      Call or Text:
      801) 489-8697
      Email at:
      [email protected]
       
      Happy riding!!! 🤘

    • By Will Sutton
      I've got a 2023 UT400 (bought from tractor supply) and I've been beating my head against a wall with it.
      It will start and idle perfectly. The second I touch the throttle it sputters and dies.
      I've checked that the fuel pump is working  (it is).
      I've replaced the injector, throttle position sensor, O2 sensor, and intake air sensor. All with no change.
       
      I've just taken a look a the schematic, and there is a crank position sensor as well.

      Could this be the source of my troubles? If so, where is this thing located? I can't seem to find it on any drawings from the parts suppliers.
    • By russnropes
      For the life of me I cannot find the directions on how to change the display to the standard for the USA - MPH. Not sure why Tractor Supply didn't do it before I bought it but it is what it is. Does anyone have the instructions to do this. I have the 2023 T Boss 550 just to be clear.
    • By felo72
      Hello all. I purchased a brand new Massimo Buck 250 EFI in June for our farm and I've had the parking brake fail on me twice. I have approximately 250 miles on the vehicle. The first time was less than a month after receiving the UTV. We all of a sudden lost brake pressure and it would not start. I tracked the issue back to the parking brake. Upon removing the chain cover, I noticed the brake pad was missing and the caliper piston was touching the rotor. I found a set of brake pads online and replaced them myself. It's worked for several months and just happened again. Seems like a design flaw. I'm reaching out to see if there's an upgrade option available, or if I should replace the entire caliper with the brake pads? Thanks in advance for any advise.
      I submitted a warranty claim, so I'll keep this updated with what Massimo replies.
      When I replaced the brake pads the first time, back in July, my Son made a video on YouTube to show the unique caliper design. Here's a link if you wanted to check it out:
       


    • By Fishing Wiskers
      Top speed is 30mph on flat grass ground.  but it will not go up minor hills forward or reverse without a runing start.  If you start at the bottom of the hill machine will stop about 1/2 way up.  I have the engine cover off and you can see the outside of the drive clutch will stop spining., and the engine does bogg down some.  Dosent matter if engine is cold or warmed up.  Seat belts are connected.  Fuel is clean
      I am the 5th shop to look at it and different shops have replaced the fuel pump, injector, ign coil, wet clutch, 
      I am not sure how to check for codes with this machine,  can anyone teall me how to do it?
       
      Compression with hot eng is 145,  valves adjusted to .005 with a cold engine.  Dash shows 426 hours
      I am not convinced it's an engine problem
×
×
  • Create New...