Quantcast
Jump to content


Cub Cadet Transmission Problem

Imtoorelaxed
 Share

Recommended Posts

Imtoorelaxed Newbie

Imtoorelaxed

Posted
Posted

I recently purchased a used 2016 Cub Cadet 750 Challenger Crew.  It has never really ran very smoothly. I just replaced the clutch which was badly worn. But when driving in high it revs to 5400 but doesn’t seem to shift into high gear. It only reaches 20mph. I’m using Amsoil 10w40 Utv oil. It also sputters at that RPM range. I’ve ordered a new injector and am going to add a fuel filter. I’m hoping that will help with the sputtering but it the transmission issue I would like some suggestions on. Thanks.  
 

 

Imtoorelaxed Newbie

Imtoorelaxed

Posted
  • Author
Posted

Thanks Travis.  Now that you mention that I remember reading about that somewhere too.  And i was't buckled when i took for a test drive.   The indicator on the dash is on/off sporadically too.  Previous owner must have tried fixing an issue with them as all four buckles are taped together, probably trying to trace problem.  It's at my cottage, I look at that this weekend.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Gary Odom
      Tracker 800sx crew 2023
      By Gary Odom
      Noticed the radiator reservoir has a pin hole leak at the seam. unit has less than 600 miles. Anyone else have this issue.
    • bms stallion owner
      BMS UTV sluggish acceleration issues/ final gear oil maintenance concerns
      By bms stallion owner
      hello, my BMS Stallion 600 is having accleration issues. the manual fails to show final gear oil diagrams very well... I have the owners manual and suspect issue is associated to transmission , I want to check the level of the gearoil. I located a drain plug (but not the fill plug nor dipstick). It will run - but wont exceede 2mph. Troubleshooting suggestions or comprehensive manual suggestions? Thanks
    • Bryan g
      Coleman UT400 shift issues , grinding .
      By Bryan g
      We see a lot of the UT400 with shift problems, not going into gear, popping out of gear, grinding etc. There  is a bulletin Im sure everyone has saw about adjusting shift cable.  That dont always fix it.  I went round n round with coleman  on couple units. We are a Coleman warranty repair center"AFS Small Engine Repair "   I told them shift lever does not have enough travel .  No amount of cable adjustment  will increase travel . I  extended lever with piece on flat  iron by 3/4 of inch .  This gave shifter enough travel to properly engage into gear completely .  Last couple units to come in for this Coleman sent me a modified shift lever, with longer travel . Problem solved! Also , heads up if you get any new unit ,,,go over and check it out,  grease  all zerks, check air filter for being in backwards, check wiring harnesses for rubbing on rotating parts,  brake hose  routing , make sure not touching exhaust .  These are just  few of the more common failures I see .

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...