-
Similar Topics
-
By staind
Looking for information on installing a OBD port or a lite to read codes in ECM.
I can not find a OBD port or a lite to read codes on this R2 with 800cc.
I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking.
This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
I want to know what the ECM is reading to help dio it.
This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever.
thanks Dan D. aka staind
-
By Cletus
I have a 2016 550, ive tryed the hisun website and seems i cant get parts there. I would like to add power steering, have seen a few "kits" on ebay
for the 750 not sure if its the same parts needed for the 550, there is a factory bracket already welded to the frame above the standard steering rack, is this to be used
to mount the eps motor? There is also a grey plug hanging just above the brake master cylinder, not sure if thats anything that needs to be used in the install.
Handy with wrenches so if i can find the parts installing it shouldnt be a problem, anyone done this upgrade, was it worth it?
-
By Steve Waldner
I have a Kioti Mechron utv and want to add power steering. Can anyone till me if there is an electric assist motor from a car that would work putting between the steering wheel and steering box. One that doesn't need alot of electronics
-
By rsar
So I finally got my Quad Gear cab enclosure after waiting out the backorder for three months and to say it's been a huge disappointment is a pretty big understatement. I think mostly because I could make it work, if not for one major issue. The windshield is right next to impossible to see out of. It's a real headscratcher because the side and rear windows are okay. It's not high quality 30 or 40 gauge marine vinyl but I have Quad Gear's stand-alone winshield so I knew it wasn't the best in terms of visibility, but definitely doable for the price. Incredibly, the side and rear windows of the cab eclosure are just as clear as the stand-alone windshield. And the windshield on the enclosure is like 50 percent worse than the stand-alone. It's the same company! I don't get it. If it had just been the rear windshield that was that bad I would have kept it. There are some creases and wrinkles here and there, but I've been using the stand-alone windshield for the past three months so it's good enough not to have to shell out $600 plus for the stock hard windshield. I'd put visibility at about 65- 70 percent. The wife hates it though, which is a pretty big negative. In any case, my original plans were to have an upholsterer change the crappy vinyl out for the high quality stuff and I even sent it to a guy who ended up flaking out on me and refusing to do it. He said he didn't want to charge me $400 for something I paid $200 for. Long story, short, I decided to return it and just get the insanely expensive Kawasaki enclosure next winter since the frigid temps here are about to start climbing in a couple weeks anyway. I first put it on just to see how it would look (I took pics of course) and found that it didnt even seal 100 percent and made it drafty inside the cab. So make that two major issues. At least with the stock enclosure everything will be top flight. Doors will be nice too.
-
-
By SouthernGypsy
We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
Trying to figure out where it belongs...
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.