Quantcast
Jump to content


Massimo Gunner 250 not charging

Ted Schleicher Jr
 Share

Recommended Posts

  • Alex changed the title to Massimo Gunner 250 not charging
Travis Grand Master

Travis

Posted
Posted

There are two main components most UTV's use for charging the battery, the Alternator (sometimes called a Stator) and a Voltage Regulator (sometimes called a Voltage Rectifier)

the alternator produces the A/C voltage... generally around 25 to 30 volts while idling and running, the Voltage regulator then converts the A/C voltage to D/C voltage  through a series of Diodes and resistors  and stuff i don't know much about, and converts it down to a low amperage  usually   .5 to 1 or 2 amps on healthy battery, but it is capable of  providing anywhere from 10 to 20 or even 40 or 50 Amps, to run accessories. dependent upon the machine what the manufacturer designed for.

you will definitely need a service manual if you want to fix this your self, i did some research and it appears the HiSun Strike 250 is the same as the Massimo Gunner 250, so this should cover it for you.

It is a free download from our library here , or you can purchase a paper copy on Ebay for about $50 or one from a Hisun dealer for $100.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • SouthernGypsy
      Help needed, Anyone recognize where this Internally Threaded Bolt belongs?
      By SouthernGypsy
      We have a 2018 Cub Cadet Challenger 400 and I found this Internally Threaded Bolt with a 10mm head size laying in the floor of the shop bay here on our ranch where we park the Cub Cadet.
      Trying to figure out where it belongs...
       




    • se3388
      Anyone else with a UT10X?
      By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
    • Texjpr
      Help! Hub safety-hour meter switch problem
      By Texjpr
      2002 ranger 500 4x4 stopped running and wouldn't restart. Service manual wiring diagram helped identify the hub safety switch as the culprit. Using jumper wires to bypass  switch allowed the engine to start and run normally. Inspection of switch showed melted epoxy and a strong smell of burnt electrical. Unable to find replacement part either used or new. Is there a work around other than jumper wiring?
    • mark walkom
      sector e1 regen has stopped (mostly) working
      By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...