Quantcast
Jump to content


Recommended Posts

Posted

The E1 has a small 12v battery to run the instruments, lights etc. You can't connect a light bar to the Discover Dry Cell batteries. Individually, they are 6 volts, but there's eight of them in series to make 48 volts that runs the motor. In the battery compartment under the seat, you'll see the dry cell batteries, but also a smaller ATV-type 12v battery directly underneath where you sit to drive. There's a fuse and relay box down there too. I'd recommend not fiddling around in there unless you're absolutely sure what you're doing, as the 48v system could cause you a nasty injury if you short it by mistake.

On the UK version, there's a 12v accessory point in the dash along with all the control buttons. There's also a 12v supply to the registration plate light on the underside of the tilting load bed. Either of those should be safe to tap into for a light bar, and are only live when the ignition is on.

  • Like 1
Posted

Never take a 12v tap off the main traction pack. However tempting that may be. If you tap off from a single battery (or two on the Hisuns 6v batteries) that 12v battery (6v batteries) will end up at a lower state of charge than the rest of the pack. This will then impact on the way the vehicle drives , as that lower voltage battery (ies) will reduce the overall performance. Unless you then do significant over charging (All batteries will then get hot) they will never get re balanced again.  And excessive overcharging will cause damage to all the traction pack batteries. Anything attached to the 12v battery or accessory should have its own fuse. As a guide dont put anything on that pulls more than 10a without talking to the dealer as how best to do that.  Especially if the vehicle is still under warranty.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • By CSM_Retired
      This is for all of you Kioti Off-Road UTV, SxS (Side by Side) owners. Discussions about Kioti Off-Road specific topics including the Kioti Mechron, K9, 2400, and 2440 models. 
    • By Gorj
      I am going to replace the batteries in my E1. I am not interested in the high cost Lithium or the expensive 6 volt dry batteries.  I am considering four 12 volt deep charge marine batteries. I have a source for 810 amp units for about $100 each.  I have no worries about reprograming the charger because it went out a few years ago and I replaced it with generic golf cart charger. When I decide to do this, I'll keep you posted on the results.
    • By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
×
×
  • Create New...