Quantcast
Jump to content


2019 Coleman Outfitter 550x wont shift into 4x4


Dr Mark

Recommended Posts

2019 Coleman Outfitter 550x will not shift front axle into 4x4. I have checked fuses, replaced the dash 4x4 selector switch, removed rear of front axle housing and tested the

axle shift motor using "C" batteries and it worked both directions as it should, but when re- installed it still will NOT shift into 4x4. It has never been run off road and has 37 on it miles.   There

are 2 electrical plugs at the front axle and I am not sure which points I should be testing to rule out a faulty wire.

Any helpful ideas would be appreciated. 

Link to comment
Share on other sites

2019 Coleman Outfitter 550X not shifting into 4X4 - ok I removed the front axle 4wd shift motor and it continues work fine using small batteries, but

when I plug in the system electrical it still fails to operate. I did however notice that one of the electrical pins on the 6 wire plug, was not flush with

the others. I took needle nose pliers and moved the pin back into place and then ensured it stayed when re-connected to the motor.

Yup it was the electrical plug connection. Now it shifts in and out of 4x4 again. So, double check your plugs and pins....

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Jim Kessell
      2005 American Landmaster
      EH65 Subaru Robins
      spits fuel from breather hose into the air cleaner and then down into carb.  What’s causing this ??
    • By Eagle Mountain Outfitters
      Our R&D team just finished the first unit and wanted to show you guys. Need more cargo space without losing the functionality of being able to fold down the seat to use the full bed? Eagle Mountain Outfitters, the maker of the original metal UTV roof, has designed a foldable rear cargo basket to meet your needs. Price is $625 + $30 shipping.  If you have any question's, please reach out to me at [email protected]
       

    • By amiracle40995
      I’m getting a 700-7 every startup. I’m having to change the plug every 100 miles on 93 octane gas. I got a lower numbered plug that is supposed to burn hotter. I’m wondering why that comes up every time I start it and if it’s related? I included a picture of the code or whatever it is. I haven’t seen the code in the owners manual or the hisun shop manual I have. 

    • By Travis M
      Just purchased a T-Boss 760 and before putting any miles on it I'm going over all the fluids, grease and problem areas that I've read about online because I know the factory quality control is garbage. 
      I've seen where everyone seems to have leaking axle seals after 2-300 miles on the T-Boss 550 and 760. I think I'm going to switch from the bellow-style diff breather to the automotive style diff breather that they use on my Tacoma and various other vehicles. I'll still keep it extended and infact run it even higher, probably into the air intake box, but I'm hoping this is what's causing the axle seal leak issue on these vehicles.  
      I'll do the modification and report back every couple hundred miles and let you know. I currently only have 8 miles, so it will be a few months before I find out if mine leaks like everyone elses. 
    • By Will Sutton
      I've got a 2023 UT400 (bought from tractor supply) and I've been beating my head against a wall with it.
      It will start and idle perfectly. The second I touch the throttle it sputters and dies.
      I've checked that the fuel pump is working  (it is).
      I've replaced the injector, throttle position sensor, O2 sensor, and intake air sensor. All with no change.
       
      I've just taken a look a the schematic, and there is a crank position sensor as well.

      Could this be the source of my troubles? If so, where is this thing located? I can't seem to find it on any drawings from the parts suppliers.
×
×
  • Create New...