Quantcast
Jump to content


"Enos, you Dipstick!"

Travis

By Travis
in Kawasaki UTV SxS Forum

 Share

Recommended Posts

Travis Grand Master

Travis

Posted
Posted

The Transmission dipstick on my mule is plastic, i've always had trouble threading it back in, because if it starts to cross thread or go in crooked, the plastic gets cooked and it's a PITA to get it to catch just right to screw in. ( i bought a new one a year or so ago)
I was wondering if i could have a metal one made.. but i have no idea where to look or who to ask.
16115-1060

And the way it's made, it only has threads on 2 sides...

 

61zWbiEwgmL._AC_SL1500_.jpg

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Homeowner A
      Diagnostic Trouble Code Help?
      By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • rsar
      Washing Mule Underbody
      By rsar
      Hey guys. I was wondering if anyone pressure washes their Mule underbody. Three years in, I have yet to do this. I'm worried that the pressure washer could damage or dislodge something but it's gotten to the point that it could use a bath. Any thoughts?
    • TjB
      2510 Kawasaki mule Diesel
      By TjB
      My dad has recently acquired a 2510 Kawasaki mule Diesel powered. It worked fine  few weeks and then quit driving. Put a new belt on just to see. Still not driving. It already had a new clutch. Belt turns when in drive or reverse and back wheels are off ground to test. But wheels not turning. Thoughts? 
    • Will D
      Mule 4010 trans overheating
      By Will D
      Hello, I have a mule 4010 trans that appeared to overheat based on the temperature light on the dash and it went into limp mode.  No steam though.  After letting it cool and the next day, I drove it around quite a bit and it did not have any problems.  Any ideas on this.  Do thermostats work intermittently?  I would like to fix the problem, looking for advice.  Many thanks 
    • tuell
      Transmission will not engage
      By tuell
      Hi everyone I have a 2016 hisun vector 550 with 1320 miles on it I recently replaced the clutch the bell the belt the one way bearing basically everything inside the primary and drove approximately one mile my side by side just stopped pulling... no noise no smoke nothing the belt is still good but it's like the transmission will not engage in any gear any help would be greatly appreciated.... I have lifted the rear end and started the side to side put it in gear Wheels do not move but you can turn them by hand

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...