Quantcast
Jump to content


Recommended Posts

  • 4 months later...
Posted

I have the bulldog 700 with the eh65. Never ran right from the git go. Carb defective. Subaru worked with me and furnished pars need. After that it ran well for some time. American Sportworks offered nothing. Their service sucks. Through mistake of my own, let grandson free on the wiring and fried both coils. Found a pair of used ones and got it running again then gov started giving me problems. I'm tired of pulling the engne to change parts on an obsolete engine. 

i do not need that much horsepower. I don't even use 4 wheel drive. Has anyone ever replaced that subaru with a Kohler 13 hp. It should work just as good as a golf cart.. Any idas or comments?

Posted

I have a bulldog 700 as well, the governor is giving me problems too..  LOL!  I hope to get the keyswitch to fix the carb backfire preventer in the Start position.  It has never worked right.  I hope this fixes it.  We have been using carb cleaner to start it for years.  I pulled the carb out, it was clean as a whistle from all the cleaner.  I finally hooked up a wire to the backfire preventer with a alligator clip and got it starting great, but I’m just tired of having to do anything to start it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By CSM_Retired
      This is for all of you Kioti Off-Road UTV, SxS (Side by Side) owners. Discussions about Kioti Off-Road specific topics including the Kioti Mechron, K9, 2400, and 2440 models. 
    • By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • By Dennis
      I have  a bulldog i bought from home depot in 2013.  In the last season it started refusing to shift from neutral to either forward or reverse.  I changed the trans axle fluid and made sure the cables were lubricated and free.  With a lot of coaxing, I can sometimes get it to shift.  once I start driving it, things improve until I let it set awhile.   Any suggestion on where to go from here?
    • By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
    • By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.
×
×
  • Create New...