Quantcast
Jump to content


2013 hisun 500 efi utv. No fuel, no spark

Robby

By Robby
in Hisun UTV SxS Forum

 Share

Recommended Posts

Robby Rookie

Robby

Posted
Posted

Hello, I have a 2013 500 utv hisun. Was running ok and cut out while parked. Bike will not start now. It turns over, but won't fire. I have no spark and no fuel. I replaced fuel pump, ignition coil, spark plug, cdi, voltage rectifier and all the fuses and relays. Could bad stater cause no fuel because I can't hear the fuel pump priming. Any info on where to start looking for problem.

Robby Rookie

Robby

Posted
  • Author
Posted

There is no kill switch. The battery is fully charged. waiting on new magneto, hope this will solve the trouble. If not magneto it has to be in the harness somewhere. Could maybe be bad ground?

  • 2 weeks later...
Greg Kilgore Community Regular

Greg Kilgore

Posted
Posted

My 2013 Uforce has a red push button kill switch on dash left of steering wheel.

 

Look and see. May be something you missed. May not be there.

Could use multi meter and check for voltage at fuel pump plug.  Possibly trace back wires.

 

But fuel pump not working and no spark sounds like a roll over protection switch or relay that needs to be reset.

Savage3 Contributor

Savage3

Posted
Posted
On 9/17/2021 at 11:46 PM, Robby said:

There is no kill switch. The battery is fully charged. waiting on new magneto, hope this will solve the trouble. If not magneto it has to be in the harness somewhere. Could maybe be bad ground?

If magneto didn't work, check trigger coil at stator, check coil, then look for grounding issue. Review service manual that Travis posted above for specific testing/troubleshooting procedures for your model. The manual provides step by step guidance. 

  • 6 months later...
  • 2 weeks later...
Greg Kilgore Community Regular

Greg Kilgore

Posted
Posted

I reread the posts and got me wondering.

I had a TroyBilt generator with B&S engine. I changed oil one summer. Started gen and all was good.

Well winter rolled around. Power went out. Went to start gen and it wouldn't hit a lick. Done everything I could and was still sitting in dark. Next day still no power. Gen still wouldn't start UNTIL I pulled the LOW OIL SHUTOFF WIRE.

Wonder if his machine or any in general has a low/no oil shutoff? That would explain the running and shutoff if parked unlevel and it tripped the no oil switch. If it has one.

  • 6 months later...
Adam Payne Newbie

Adam Payne

Posted
Posted

So I had a customer with a 2015 hisun vector 500 that had no spark the fuel pump would not prime it ended up being there is a purple wire that is in the wire loom that goes from the dash instrument panel back to the fuse box (cdi) to fuel pump that wire needs constant 12v and mine didn't so that how I found the break

  • Thanks 1
  • 1 year later...
Greg S Newbie

Greg S

Posted
Posted

I have a vector 500 I have no fuel ,no spark ,,,I put a wire straight from battery ground to the left wire of the fuel pump and it primed with key,,, could this be the purple wire your talking about cuz I still have no spark

  • 2 weeks later...
  • 1 month later...
vachi Newbie

vachi

Posted
Posted
On 9/6/2021 at 3:46 PM, Robby said:

Hello, I have a 2013 500 utv hisun. Was running ok and cut out while parked. Bike will not start now. It turns over, but won't fire. I have no spark and no fuel. I replaced fuel pump, ignition coil, spark plug, cdi, voltage rectifier and all the fuses and relays. Could bad stater cause no fuel because I can't hear the fuel pump priming. Any info on where to start looking for problem.

did you ever figure out the no start issue?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CSM_Retired
      Kioti UTV SxS Forum
      By CSM_Retired
      This is for all of you Kioti Off-Road UTV, SxS (Side by Side) owners. Discussions about Kioti Off-Road specific topics including the Kioti Mechron, K9, 2400, and 2440 models. 
    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Bobbers
      Axis 500 parts
      By Bobbers
      My wife accidentally ran the Axis 500 into a fence and tore the front end up (broke her arm too). Just wondering where the best place to get front end parts? I know she busted the knuckle but haven’t jacked it up yet. Thanks guys for any help!
    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...