Quantcast
Jump to content


Recommended Posts

Posted

First time poster - new member. Most issues between my pioneer 700 and Challenger 700 I’ve been able to fix without issue. This problem is a different story. Have a 2016 Challenger 700 that overheated due to cooling fan not coming on. Changed both temp sensors on thermostat housing as well as radiator temp sensor. (Being that unit overheated I teplaced to be safe) Put power to fan to verify operation - works great. Checked all fuses, connections ect. No issues found. Verified coolant level and air bled out - all good. Using a temp gun I Can see temps climb to 210 at thermostat housing and 195 at rad at sensor location and fan won’t turn on. Any help on where to check or any wiring schematics for this unit ?

Posted

Update to diag. No power found fan (blue wire) ground through rad switch seems present. Traced back wire and appears to go direct to ignition switch? Is this correct ?

Posted

Rhino has a snubber diode in series with power feed from IGN switch.  Clones also have same.  The diode OPENS.....thus no power to FAN.  Test by jumping in 12V when radiator warm.  If thermo switch is good and no air in coolant....have fan.  The bad part.....the diode is part of the wiring harness.  Hard wire the "jumper" IGN switch feed and don't waste time looking for diode.  Post back results.

Posted

Went back and verified your diag and that is the issue. Thank you. Got tired of working through the excess and unnecessary method of controlling the fan. Ended up ordering a 22mm rad hose sensor adapter with a 175 degree sensor which I’ll install to piggy-back the factory system that seems to constantly give issues. The $65 is worth the insurance if the factory components fail again.

  • 8 months later...
Posted

Would you guys be willing to tell me where this diode is located at in the harness. I'm fighting what I believe to be the same problem. 

Any help is appreciated.

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By Poppateets
      I just purchased a used 2023 Massimo warrior UTV SxS 1000mx with 600 miles on it. I didn't even get a full day of riding and the driver's side rear axle broke. I'm pretty sure it was already going bad because we would hear a noise once in a while. I'm wondering if anyone else has had problems with theirs. Also looking for places to buy accessories.
    • By Frank in MI
      Thanks for accepting me!
      Haven't got a side by side yet, but have been shopping.   
      Any advice welcome & I am on a limited budget, so haven't decided yet on new or used.
       
    • By hisun junk
      As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

    • By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • By Eagle Mountain Outfitters
      Our R&D team just finished the first unit and wanted to show you guys. Need more cargo space without losing the functionality of being able to fold down the seat to use the full bed? Eagle Mountain Outfitters, the maker of the original metal UTV roof, has designed a foldable rear cargo basket to meet your needs. Price is $625 + $30 shipping.  If you have any question's, please reach out to me at [email protected]
       

×
×
  • Create New...