Quantcast
Jump to content


2007 Polaris Ranger XP cough at 3/4 to full throttle

divecaptchris

By divecaptchris
in Polaris UTV SxS Forum

 Share

Recommended Posts

divecaptchris Newbie

divecaptchris

Posted
Posted

I have a 07 700Xp Ranger, 320hrs, the machine started to develop a cough at 3/4 to full throttle. The Machine runs perfect other than that, and will cruise down the road at 5900 RPM with no issue. If you stomp the gas from idol or low RPM it wont start the issue until the RPMS get above 5K, if you running 3-4K it will do it as soon as the throttle reaches 3/4 open. I have changed the plugs and read them, look slightly lean but not bad. No codes except and code its had since I owned it for the transmission. Tested fuel pressure, its right on, looked for air leaks around the boot, found none. I also changed the belt just to make sure it wasn't a slipping issue that the tach didn't show it getting to the rev limiter. Any help would be GREATLY appreciated

  • Alex changed the title to 2007 Polaris Ranger XP cough at 3/4 to full throttle
divecaptchris Newbie

divecaptchris

Posted
  • Author
Posted

Just started it a few weeks ago, I did notice an issue with voltage to the battery this weekend, suspected the voltage regulator bat was 12.4V when i started the machine it went to 11.8 and would only come up to 12.2 at 3000 RPM. No starting issues though! I took the VR off and tried to get a new one but Polaris was out, so I put it back on and it was charging normally again, but still popping. I also noticed that tach shows it idling at 970RPM but sounds more like 6-700 RPMs to me. I got a new VR coming this week. hoping it fixes  all the issues... 

kenfain Experienced

kenfain

Posted
Posted

After re-reading your original post, I see you've considered the limiter. If the VR doesn't fix the problem. I'd wonder if it's a gummed up fuel system? Since there's no codes, and very low hours.

I've found, that if it starts, and runs, and that's the problem, then there's hope of it self cleaning, by running it enough.

I'd try adding some seafoam, and run it, see if it improves after a tank of fuel, or so. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • ToughLuck
      2021 Massimo MXU 1000 Runs Rich
      By ToughLuck
      I have a 2021 Massimo MXU 1000.  Last winter the front drive shaft sheared off inside the motor and it was cheaper to buy a new motor than to take it apart in order to remove the front drive shaft that was broken inside the case…
      Now it is running rich, seems to maybe be geared too high, does not accelerate well once you hit about 28mph.  I’ve replaced the O2 sensor.  MAF is next (I accidentally ordered the wrong one, but when I removed the old one you can clearly smell fuel).  
       I’m not a motorhead but I can turn a wrench.  Any ideas how to get this motor optimized?  The motor has about 300 miles on it.  I broke it in as recommended in the manual. 
    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Flanman55
      No crank issue
      By Flanman55
      2007 Hisun HS700  will not crank.  Replace the ignition switch. Same thing.  Replaced solenoid by the battery same thing. Can jump it and it starts good across the solenoid posts. Ran a jumper wire from switch to solenoid. Nothing 
       
      can anyone suggest something else. 
    • SpaceGhost
      New guy with new (to me) machine
      By SpaceGhost
      As with any forum you join, there is a requirement for an obligatory introduction... and that seems fair. How else do you get that first post in there without jumping in with some stupid question right out of nowhere?

      Hi. I'm Space Ghost. Well, not really, but that was my call sign on my last deployment before an IED made me non-deployable, and I an now retired/disabled, and living on my wonderful VA disability. I did almost 28 years in total between the Army, Army Reserve, and National Guard. 1 deployment with the Reserve (Desert Storm) and 3 with the Guard (1 pre, and 2 post 9/11)

      Married (going on 30 years) one of each. (both out of the nest)
       
      Just picked up my first side by side a couple days ago. A 2020 Can-Am Defender HD10 DPS 6x6. 

       
      It's in pretty good shape, but as you can probably tell, it's sitting a bit high. Former owner put a lifting collar on the shocks. 

       
      The good = almost 17" of ground clearance. (30" tires) 
      The bad = incredibly steep driveline angles, and a pretty stiff ride. 
       
      They will be coming off. 
       
      Other than that... clean as a pin and appears very well maintained. 
       
      Looking forward to seeing what this forum can bring, and hoping I can bring something in return. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...