Quantcast
Jump to content


2013 Cub Cadet Volunteer has gas on the engine oil

jaynrobs

By jaynrobs
in Cub Cadet UTV SxS Forum

 Share

Recommended Posts

  • Alex changed the title to 2013 Cub Cadet Volunteer has gas on the engine oil
Travis Grand Master

Travis

Posted
Posted

Most common problem is the float needle in the carburetor has failed. it's job is to meter fuel flow into the carb bowl as needed, Requiring a carb rebuild or replacement.

Do you have the model number of the engine or machine?

  • Like 1
T-boss 410 Experienced

T-boss 410

Posted
Posted

My first guess would be the piston rings are bad and your getting blow by. Don't know if there's a PCV system on your Volunteer, but if so I would check that to see if it's clogged. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • boydog40
      2008 landmaster lm650 engine swap wiring problems
      By boydog40
      my subaru gave it up, bought a new Predator 670cc
      problems is, wiring the buggy to the new motor, OEM key switch has 5 wires (red, green, yellow, black and brown)
      new motor has many more wires than the Subaru and i have no idea what goes where!!!
      finding any info on the web is almost impossible to do also
      any help will be greatly appreciated!
      thanks guys
    • Homeowner A
      UT400 First Oil Change Overfull Milk Chocolate What to Check
      By Homeowner A
      Picked up an essentially new 2022 UT400 with 9 miles on it.  Decided to change the oil because it's probably never been done.  Pulled the dipstick and noticed it was overfull then went and pulled the drain plug and took off the filter and it was like brown water running out.  What should I start checking?
    • Cory J
      2023 t-boss 550 belt slipping and found oil in belt housing
      By Cory J
      Belt started slipping when I used it in high gear. It works okay in low unless I'm trying to power it up a hill and then it slips.., Ordered a new belt and went to change it and found a good bit of oil in the belt housing. Has anyone experienced this? Belt looks fine. Only have 300 miles on this thing..
    • Reynolds Rocket
      2017 Intimidator XD4 800 Check Engine
      By Reynolds Rocket
      I have a 2017 Intimidator XD4 800cc 4x4.  It will run great and then it's like it goes into safe mode and only runs on 1 cylinder.  It's not fouling out the plug when it happens.  Some times when I stop and restart it, it works fine.  First I thought it was a spark issue, then a fuel issue, but I feel like it's a short in the wiring some place. 
    • eManualonline.com Save 30% OFF Sitewide, Use code: XMAS30
    • lmarkie
      Bulldog BD700 Engine Swap
      By lmarkie
      I swapped out the Subaru motor for a Predator 670cc. If I remove the heat shield around the muffler, The stock muffler sits in there just fine with 1" to spare.
      Only problem is the exhaust exit is toward the back seat instead of out the back.
      Do you all think that the stock exhaust would be okay (just as effective) if cut a hole and welded a pipe on the reversed (opposite) end? Of course, plug the old exit end. Other option I thought of was to roll a tube 180° with a 7" center line radius and finish extention of 12" or so.
      Any thoughts?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...