Quantcast
Jump to content


I have a 2008 Joyner Trooper 1100 T2. The Initial 3 second start up sequence will not go, but motor will turn over.

California Nut case

By California Nut case
in Joyner UTV SxS Forum

 Share
Go to solution Solved by mixfixdave,

Recommended Posts

California Nut case Rookie

California Nut case

Posted
Posted

I have a 2008 trooper 1100 T2 which ran great, but the starter would not engage for a lot of clicks. I changed out the starter, careful to note one wire on the solenoid and 4 wires on the main starter motor post. After I finished, the start sequence where the two gages sweep back and forth and the fuel pump and fan turn on for 3 second, stopped working. I can not find any bad or loose wires, I tried changing out the ECU and can not find anything apparently wrong. Does anybody know what sensor error stop the initiation sequence.?

California Nut case Rookie

California Nut case

Posted
  • Author
Posted

Dave, Thankyou for the reply. I've checked all the fuses and tested and swapped around the relays. I can hot wire the relays and the pump and fan run fine. I appears that the ECU is seeing some sort of error condition that will not allow it to start. I am new to the trooper world but have been wrenching for years. Not to good with the computer control stuff.

California Nut case Rookie

California Nut case

Posted
  • Author
Posted

Dave, You nailed it. I had pulled two smaller wires to the starter that apparently were ground leads to the engine block. I took them off the starter and ran them through a small ground wire just in case, and it immediately did the warm up sequence and then started. I still need to check the wires to make sure that both of them go to the ground, but that is what looks like the problem. Thanks very much for your insight. Next time I better pay better attention to the wires when I take them off.

  • Like 1
mixfixdave Enthusiast

mixfixdave

Posted
Posted

It is 3 small wires to one ground connection. All the wires are bundled together.
I’m on my 3rd starter in 7,000 miles of off-road. The most recent one I purchased spins the motor much better than the stock one or it’s replacement.

California Nut case Rookie

California Nut case

Posted
  • Author
Posted

Wow, I spent a lot more than that. I think I paid $150 for it from Amazon. Funny thing is now the motor runs and all my running lights quit. That should be a lot easier to find. Weird part is that all the fuses are good, and it was working while the engine would not start. Go figure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • boydog40
      2008 landmaster lm650 engine swap wiring problems
      By boydog40
      my subaru gave it up, bought a new Predator 670cc
      problems is, wiring the buggy to the new motor, OEM key switch has 5 wires (red, green, yellow, black and brown)
      new motor has many more wires than the Subaru and i have no idea what goes where!!!
      finding any info on the web is almost impossible to do also
      any help will be greatly appreciated!
      thanks guys
    • Nutcase
      Joyner trooper Fuel injection
      By Nutcase
      I have a Joyner Trooper 1100 4 place that has been sitting for a number of years. I have everything taken care of but i can't get the fuel through the injectors. Fuel pump puts full pressure on them but they don't turn on or spray fuel. Any ideas?
    • hisun junk
      2017 Cub Cadet Challenger 750 hisun junk motor
      By hisun junk
      As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

    • Jacob E freeman
      2018 cub cadet challenger 750 over heats no one knows why
      By Jacob E freeman
      I have a 2018 cub cadet challenger 750 I bought brand new almost 2 years ago the first month I had it the exhaust broke and burnt the spark plug wire in two that was a recall so the dealership installed the new one it had a different design and it bolted up to the bottom two plugs below the spark plug the dealership said they had to Adjust the exhaust valves I get the machine back thanking everything is good now wrong not even a week after I get it back the timing chain tensioner comes apart inside the motor I take it back to the dealership They put one on I get the machine back thanking everything is good but then just like before not even a week goes by when I was riding the Machine automatically quits going come to find out the wet clutch was burned up the primary clutch head stripped off of the splines I get that fixed and then  it overheats I take it back they bleed the air out of the coolant they bring it back to me the same day that I get it back it overheats again I take it back they temporarily fix it again just enough to let the warranty run out and now the machine has been to multiple different mechanics I have had them try to bleed the air out they have stood it up on its end I have had the water pump changed I have had the fan hooked to a switch so I could leave it on all the time but still almost 2 years later not even 200 hours on the machine and I cannot ride it The dealership will not take it back as a lemon I have tried I am at my wits end I have no clue what to try next
    • Hunterman22
      2021 Hisun Axis 500 No Start - Need Help Please
      By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...