Quantcast
Jump to content


I have a 2008 Joyner Trooper 1100 T2. The Initial 3 second start up sequence will not go, but motor will turn over.

California Nut case

By California Nut case
in Joyner UTV SxS Forum

 Share
Go to solution Solved by mixfixdave,

Recommended Posts

California Nut case Rookie

California Nut case

Posted
Posted

I have a 2008 trooper 1100 T2 which ran great, but the starter would not engage for a lot of clicks. I changed out the starter, careful to note one wire on the solenoid and 4 wires on the main starter motor post. After I finished, the start sequence where the two gages sweep back and forth and the fuel pump and fan turn on for 3 second, stopped working. I can not find any bad or loose wires, I tried changing out the ECU and can not find anything apparently wrong. Does anybody know what sensor error stop the initiation sequence.?

California Nut case Rookie

California Nut case

Posted
  • Author
Posted

Dave, Thankyou for the reply. I've checked all the fuses and tested and swapped around the relays. I can hot wire the relays and the pump and fan run fine. I appears that the ECU is seeing some sort of error condition that will not allow it to start. I am new to the trooper world but have been wrenching for years. Not to good with the computer control stuff.

California Nut case Rookie

California Nut case

Posted
  • Author
Posted

Dave, You nailed it. I had pulled two smaller wires to the starter that apparently were ground leads to the engine block. I took them off the starter and ran them through a small ground wire just in case, and it immediately did the warm up sequence and then started. I still need to check the wires to make sure that both of them go to the ground, but that is what looks like the problem. Thanks very much for your insight. Next time I better pay better attention to the wires when I take them off.

  • Like 1
mixfixdave Enthusiast

mixfixdave

Posted
Posted

It is 3 small wires to one ground connection. All the wires are bundled together.
I’m on my 3rd starter in 7,000 miles of off-road. The most recent one I purchased spins the motor much better than the stock one or it’s replacement.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Prepper
      2015 MSU-500 crank - no start
      By Prepper
      I'm working with a 2015 MSU-500.  Basic symptoms are it cranks well, but will not fire.  It has spark, and it has fuel spraying out of the injector (and spraying starting fluid into the throttle body and plug hole makes no difference).  It has compression.  I bought it not running, and no other information was available.  It has 775 miles on it and 127 hours.  It looks to be in very good shape.   Previous owner replaced fuel pump, ECU, coil, plug, and the fuse/relay box that mounts on the firewall, then gave up.
      My questions relate to cam/valve timing, considering the symptoms and diagnostics so far.  My thinking was the woodruff key sheared off and the crank spun, making it out of time.  My question is, by the pictures attached does anyone have an opinion as to the cam/valve timing being correct?  In the crankshaft picture you can see a timing mark visible.  In the camshaft picture I have arrows directed towards what I think are timing marks (which appear to be exactly 180 degrees from one another).  However, the long arrow in what appears to be bolt configuration in line with the piston/rod line.  Here is a puzzling note... in the position you see in the pictures... I have valve lash on both the intake and exhaust.  I think it's at TDC, given the visible crank timing mark and valve lash on both valves. 
      Any thoughts ?  Does this appear to be in proper valve time ?  Have I missed anything simple ?  Thanks in advance for your input.


    • rdborra
      Bobcat 2200 dump bed relay pops fuse and stalls after warm
      By rdborra
      I had to remove the relay for the dump bed due to it popping the fuse for main key power. I have tried to find a short but nothing seems to out of normal. I also disconnected the dump motor and switch and still pops the fuse. Also, when the machine is warmed up i get about 5 to 10 of work out of before it stalls. Once I can get it to start again I have to use the choke to keep it running. 
    • tuell
      Transmission will not engage
      By tuell
      Hi everyone I have a 2016 hisun vector 550 with 1320 miles on it I recently replaced the clutch the bell the belt the one way bearing basically everything inside the primary and drove approximately one mile my side by side just stopped pulling... no noise no smoke nothing the belt is still good but it's like the transmission will not engage in any gear any help would be greatly appreciated.... I have lifted the rear end and started the side to side put it in gear Wheels do not move but you can turn them by hand
    • Frank Mac67
      AXIS 500 WILL NOT START. HELP!
      By Frank Mac67
      My Axis 500 has been operating properly for almost a year with Zero problems. While I was away my granddaughter & friends were riding & playing in the snow. They went to the gas station to fill the tank & the vehicle would not start afterwards. I BEEN GIVING MULTIPLE STORIES: The ATV will not start. When I turn the key I can hear the fuel pump come on but nothing happens other than that. 
      - NO CLICK - NO OTHER NOISE
      *I CHECKED THE BATTERY 12.43volts
      *I replaced the solenoid inside the battery compartment. 
      Seems the next electrical component in line has battery connections IN & motor connections OUT with 2 other small wires connectedaswell(I do not know the name of this component).
      Can anyone help?
      I can not find an ordered list of electronic components starting at the battery.
      Can anyone help with this?
      Thanks in advance for any help.
       
    • staind
      Joyner R2 2008 800cc ECM code reader Lite or OBD port install
      By staind
      Looking for information on installing a OBD port or a lite to read codes in ECM. 
      I can not find a OBD port or a lite to read codes on this R2 with 800cc. 
      I have code readers and adapters for most ATV's. From what I've found so far. They don't have a connection for to read codes. I may be wrong. That's why I'm asking. 
      This R2 has had new IAC, TPS, MAP, fuel pressure regulator and fuel pump replaced. This was done by neighbor to try to stop surging. It still surges on start up and then settles down. But once you hit the accelerator it revs up to 2000+ rpm and stays till you block off IAC port in throttle body with finger. Once you do that it once again settles down and idles perfectly.
      I want to know what the ECM is reading to help dio it.
      This joyner is the first one I've run across. Well second one in a week. (my neighbors 2 of them) The other was a trooper with the 1100cc chery motor that had been setting for years. After cleaning up the fuse box connections. It runs like a top. Had to replace all gages with aftermarket gages. Water, oil, gas, amp. Only problem one was the water temp using original sending unit. Had to install 150 ohm resistor on the input wire to get it to read correctly + - 5 degrees. Close enough. Gas sending unit was/is for a boat tank 6" tall. All SS so it should last forever. 
      thanks Dan D. aka staind

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...