Quantcast
Jump to content


Pedal hard to press

Tim McCarley

By Tim McCarley
in UTV General Discussion

 Share

Recommended Posts

Tim McCarley Rookie

Tim McCarley

Posted
Posted

I have a 2016 tw400 with the Honda engine. It runs great. Is there a way to get the gas pedal to press easier? It is really stiff. Like the spring in just real stiff. Same thing with pulling out the choke cable. 

Travis Grand Master

Travis

Posted
Posted

First thing i would try is lubing  the ends of both cables with WD40, it will creep down the cable eventually. i would also try disconnecting the cable(s) from what they hook too and move the choke and throttle by hand, and see if if they move easy or not.

  • Like 1
  • 2 weeks later...
Travis Grand Master

Travis

Posted
Posted

Do you know the model of the honda engine? But before blaming the carburetor, i would remove the spark plug and look at the electrode end, if it's really dark/black. that would verify the carburetor is running too rich.

  • Like 1
Tim McCarley Rookie

Tim McCarley

Posted
  • Author
Posted

Also, the previous owner put an after market carb on here. It seem to run really rich. You smell gas strongly while riding. What can I adjust to make it better? 

 

The plug is really black. It is a Honda GX 390 engine. 

W B Enthusiast

W B

Posted
Posted

I'm no help with the Honda engine.  Could be the float ora stuck needle valve. Does it have an electric fuel pump. That could be too much pressure for that carb.

Travis Grand Master

Travis

Posted
Posted

It could be a fault in the carb, a lot of the aftermarkets aren't very strict on quality control. the main jet could be oversized a few thousandths and that would affect running.

The only adjustments on these Honda carbs, besides the Idle speed adjustment, is the Mixture screw on the side of it, Some of these have them, some of them don't.

If your carb has this adjustment screw, the proper way to set it is to warm the engine up, and adjust that screw in or out, until the engine reaches it's highest Idle RPM, that's where the engine is getting the most fuel. you can turn the screw in about 1/16 to 1/8 of a turn that will lean the mixture out just a little bit. you may now need to readjust the  idle RPM with the plastic screw on top of the carb.

If it still runs rich after this, most likely there is a issue with the aftermarket carb, i had a problem finding a carb to fit the GX390 on my pressure washer, i finally bought a OEM Honda carb.

 

  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • aefron88
      HOWTO- Code Scanner & Read Engine Parameters
      By aefron88
      This post will explain how to hook up your PC to the ECU of a Hisun/Coleman/Etc UTV to be able to read error codes & engine parameters for troubleshooting purposes.
      This is applicable to all small engines using the Delphi MT-05 ECU. This should cover all fuel injected Hisun models, as well as various other Chinese FI engines, as the Delphi MT-05 ECU seems to be the favored ECU solution.
      Even though we get actual engine error codes to display on the dash, sometimes we have “pending codes” (not yet confirmed by the ECU) or other intermittent issues that are hard to diagnose, for example a poorly connected sensor that may give intermittent false readings, or a sensor that’s putting out bad date, but not bad enough for the ECU to realize.
      The setup requires 2 cables, which are available for around $25 combined, a PC with a USB port, and some charityware software called “HUD ECU Hacker”. This gives the same functionality as the $300 dealer code scanner for a fraction of the price.
      In searching I found info about HUD ECU Hacker, but I have yet to see info anywhere about how to hook it up to a Hisun, so I took the leap and bought some cables, and made it work. I will show a step by step of how to do so in post two.
      I will be breaking this down into 2 posts:
      Delphi ECU Info & Overview (This post) System setup & use Delphi ECU Info (Skip ahead to the next post if your eyes glaze over technical details)
      The Delphi MT-05 ECU was developed to allow small engines to use fuel injection. A fuel injection system requires feedback from various sensors to operate efficiently. This feedback allows the adjustment of ignition timing, fuel injection volume, etc to efficiently and cleanly produce the most power possible from a given engine.
      The MT-05 ECU has a number of sensors that are required for proper functioning including; Coolant temp, crankshaft position, intake temp, intake pressure, exhaust O2, throttle position, as well as some other optional sensors that are used on more complex vehicles.
      From the sensors the ECU adjusts: Fuel injector timing/pulse, Idle air control valve, and ignition coil

      The Delphi MT-05 puts out diagnostic data, however it is not ODB2 like a modern car, where is where it gets tricky reading it. There are three options, there is an old 16 bit piece of software Delphi has that is not able to run on a modern computer, there is the motorscanner tool for dealers ($300), or there is freeware HUD ECU Hacker with the proper cables.
    • SSgt1994
      XY 600 GKE Replacement Engine options
      By SSgt1994
      Hello everyone, second time posted looking for assistance. First time you all were a great help!
      I have an 2013 XY Powersports 600GKE UTV, sweet little machine when she was running. My youngest last fall get it covered in mud, and then blew the engine. I mean she doesn't start any more, and we've even tried rebuilding it since he's in a Vocational School for Power Sports and Diesel course, but no luck.
      One of the other members (NVM"something") was really knowledgeable about the machine I had and the engine, all I can tell you is its a CFMoto. If I can't find a replacement, does anyone know if there is one that it can be easily swapped out with, or even minor modifications.
       
      Thanks!
      Myron
    • lincolnsq175
      Are there any performance parts for ut400?
      By lincolnsq175
      Ive searched and cannot find any performance parts that fit my machine.
      I have a 2020 coleman ut400.
      Im looking for machined sheave kit, programmers, cdi, exhaust and intake.
      I know these are yamaha rhino clones but are they rhino 450 clones?
       
      Any info is appreciated.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...