Quantcast
Jump to content


2017 Cub Cadet challenger 750 runs rich

motofan91

By motofan91
in Cub Cadet UTV SxS Forum

 Share

Recommended Posts

motofan91 Newbie

motofan91

Posted
Posted

Recently acquired a 2017 Challenger 750. Previous owner ran it low on oil so I had to do a top end. Starts and runs but it seems to be running very rich. There isn't too much information available for troubleshooting the EFI system. Air filter is new and I even tried running with it removed with no change. Some of the parts are relatively cheap, so I did replace the IAC and the MAF sensor. Could this be related to the TPS sensor or which direction should I head in next? There doesn't seem to be any adjustment on the TPS and I have read something about a WOT ECU reset but that didn't change anything. 

Thanks in advance

 

  • Alex changed the title to 2017 Cub Cadet challenger 750 runs rich
  • 1 month later...
  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Joe Breaux
      2017 Massimo MSU500 Thermostat Malfunction
      By Joe Breaux
      Got a 2017 Massimo MSU500 UTV with thermostat malfunction.. hot light comes on in 4-5 minutes but radiator is ice cold... where exactly is it?  The hose neck on the head has nothing in it.  I was told it was down by oil drain plug.. only thing I see is water pump.. Is in inside pump housing?  Cant find any exploded diagrams that show it.. how to I remove it? any help would be appreciated
    • Jim Kessell
      Predator 670 manual oil pressure gauge
      By Jim Kessell
      Hi All
      Just installed a predator 670 on my Landmaster. My question is can I remove the low oil pressure wire fitting and plumb my mechanical gauge into that access point?
      Thanks in advance for your advice !!
      Jim
    • lincolnsq175
      Are there any performance parts for ut400?
      By lincolnsq175
      Ive searched and cannot find any performance parts that fit my machine.
      I have a 2020 coleman ut400.
      Im looking for machined sheave kit, programmers, cdi, exhaust and intake.
      I know these are yamaha rhino clones but are they rhino 450 clones?
       
      Any info is appreciated.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...