Quantcast
Jump to content


Recommended Posts

Posted

I need some help.

 

I bought a new Renegade in June 2021 and have only put 60 miles on it and the other day checking cows I noticed the oil light on and the oil gauge reading zero and the oil light on.

 

Is there a better oil sensing unit than the factory?   I've ordered one from Joyner ($60) but would like to have a supply if they are going to go out after 60 miles. 

 

Thanks 

Posted

Was that oil light and pressure reading while idle?  Mine does that, too at idle.  The problem with Chery engines is that the oil pump barely has the volume needed at idle to maintain 10 psi per 1,000 rpms.  I put 50 weight oil in mine and it helps a little (15 psi at idle).  I bought a replacement on Amazon (VDO brand) because I thought I had the same issue.  No change.  But they are common on Amazon.  You might consider checking the oil pressure with an independent gauge (that's not made in China).

Posted

Dan,

It was hot when it went out.  I had changed oil from a 0w40 to a 10w30 (for the winter)  I have since changed oil again back to 10w40.  Still Little if any gauge response and the oil light is on.  The engine sounds fine and since it has a manual oil pump I'm not really too concerned still it's just the fact that it's practally brand new and this happened.  Only use it to check cows weekly.  Never been rained on.  No mud.  Never even had it in 4wd

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.
    • By FTG-05
      I want to ditch my Kubota RTV-XG850 and its moronic twitchy throttle design flaw, get rid of the problematic engine and the 40 mph purposely throttled speed.
      So far, I'm looking at the Honda Pioneer 1000 and the Polaris Ranger 1000, both of which have 1000-1500 lb payload bed capacity.
      What other makes and models should I be looking at?
       
      Thanks for the help!
    • By SteveS
      While driving the MSU 800, it runs good but it lately it will not go over 20 MPH. The side by side will hesitate when it reaches 21 MPH, but it will run good under 20 MPH. What is the issue?
    • By Joseph Sills
      Has anyone modified the panel lights so they can be dimmed ? I haven't found a wiring schematic for the display . 
×
×
  • Create New...