Quantcast
Jump to content


Nelson Hills ride report


Guest Lenny

Recommended Posts

Guest Lenny

Just got back from Nelson Hills near Boulder, Nevada. New suspension is much better, Fox shocks on all four corners. Needs some tuning but I first need to understand just what it's doing and why. Nelson Hills is just like the name implies, hills. The area is aprox 10 miles x 12 miles or 120 square miles of mountain foothills. We camped there for three nights. Trails are nearly endless. They roll up and down, in and out of washes, up washes and are nearly constantly turning. There is a ton of great climbing challenges comming out of the washes. Many times my wife said, "your not going to try that, are you?". I saw a lot of stuff I wouldn't try but as the days went on I found that I could point the Trooper at, well, nearly anything, and it just went up it. This was happening dispite that I had 120 pounds of survival gear on the top rack, two 5 gallon cans of extra fuel, 5 gallons of water and ice, and to add insult to injury, I not only had my 2 dobermans at 70 lbs. each but was babysitting my daughters 65 pound dog and of course my wife and I, a spare, and 20 pounds of jacks and tools. Even though I was loaded down, It didn't seem to matter. Ran the steeper stuff in second, general hills in third and some in fourth. This engine pulls pretty good at low RPM. Eventually cut a sidewall but had a spare, Hey I'm no dummy. Well, I forgot that I used a different lug nut to hold on the spare and I didn't have a socket to fit. Fortunatey, I saw a couple of cars parked with people about 1/4 mile away. Walked down and got a socket. Went back and proceeded to split it. Walked back again, offered $20 for the broken socket and asked if someone had a non tiawain socket and got a Craftsman. Made it back ok.

THE CLIMB

When I first got to the camping site, I saw a hill. Let me rephrase that, a serious hill. I've done a lot of competive motorcycle hillclimbing and If your going to try this hill you better not be a beginner, a novice or an intermediate rider. You better know what your doing or your going to get hurt. I couldn't resist, walked over and took a look and thought I think the Trooper would give it a honest try. The Trooper won but I got beat (scared) and decided that, yes, it would climb it but the consequenses of getting turned sideways was way too serious. Maybe if I was twenty and a lot dumber. I took pictures of where I stopped on the hill and some pics of the hill showing where my front stopped from different perspectives so you can get a feel of just how intimidating this hill is. I stopped on the steepest part of the hill with another equally steep part about 40' to 50' ahead of me. This section was steep enough that the loose broken rock that you see elseware on the hill wouldn't stay on this part of the slope. It was just exposed rock. Just before getting to the stopping point you see in the picture, I gave it more gas and I was actually acceleratiing as I went up the rock secton. Thats all I needed to see, It wanted to go all the way and would have. Amazing machine.

take a look at all 7 picks starting with

2170449080104282158MvPqSS_th.jpg

Lenny

Link to comment
Share on other sites

That's some hill, good story, Get an old tire iron and a deep socket out your junk tool stash and weld them together.2875841220104282158BiYCAX_th.jpg, I think I ended up using an 11/16 deep socket with 1/2 in. drive, it fits kind of tight, which is nice because the corners don't get rolled off.

kinarfi

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Kingfish
      The conversion took about 350lbs. off the vehicle.  It never rode great, but now I feel every  crack in the road.  I have backed off spring compression nut to the point just under where they would move around if suspension was at full extension, but it is still very stiff.  I would like to put some softer coilover springs on it, but I have no idea what the spring rate is with the original springs so I would just be guessing on what to order.  Does anyone have the data for the original spring compression rate?  I am willing to give up a little ground clearance for a softer ride. Right now when sitting still the rear suspension is at or near full extension and the rear tires have several degrees of camber which will cause uneven wear if allowed to continue in this state.
    • By Ridge Runner
      Hi
      i have a 2019 Coleman 550 Outfitter.  The tail gate has a pin on each side, that snaps into latch blocks that are mounted on the inside of the tail gate opening.  There are two M6x16 pan head screws(bolts?) that hold the latch blocks in place.  The screws enter from inside the bed body, and I can’t figure out how to access them.  This is right by the tail light assemblies.  I tried taking a pan head screw out of the fender lip, but found out there is not a nut firmly inplace, to hold the pan head screw in.  Bottom line I’m making it worse.  
      coleman was no help.  If I could figure out how they attached the tail light, then maybe I could put the latch screws in through the tail light hole.  Any ideas?
       
      thanks
      Ridgerunner
    • By Jon Spruill
      Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks
    • By WCF
      Hi Joyner Gang
      New to the Joyner group. I'm making long travel for the 1100 Sand viper. I'm trying to make something that will work as well or even better than the RZR Rino etc. At this time the front has 14" travel rear has 16" of travel. Still developing the suspension. comets are welcome. Ask questions and I will get back to the Forum 
       
      ?
       
       

       
       

       


×
×
  • Create New...