Quantcast
Jump to content


Wiring harness is a mess has anyone ever tore it all out and only put in the basics. Power ,ignition ,starter, stator and regulator

Hisun .500

By Hisun .500
in General Discussion - Anything

 Share

Recommended Posts

  • 5 months later...
aefron88 Community Regular

aefron88

Posted
Posted

Might get better responses in the hisun forum.

Presumably this is an EFI model. If so they need all the wiring. Replacement harnesses are available for a responsible cost ($150ish) for most hisun models. If it's EFI it needs all that stuff to function without throwing codes and going into limp mode. There's a good description on the various hisun repair manuals (download section) towards the back explaining how the Delphi EFI system ties all the inputs and outputs together and what each piece does.

  • Like 1
  • 4 weeks later...
Don W Enthusiast

Don W

Posted
Posted

If you figure your time min removing the harness and then running new wires to everything, which you need, everything you can but 2 harnesses for the price of making one

  • 3 weeks later...
Greg Kilgore Community Regular

Greg Kilgore

Posted
Posted

That is how I look at a lot of THINGS I could make. Figure in material, and my time building it vs. just buying and installing or having it installed.

Now if I'm doing it for enjoyment/relaxation/satisfaction of working on stuff that is different.

But I usually only have the weekends to piddle on stuff. No evenings. 

  • Like 1
  • 8 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Homeowner A
      Diagnostic Trouble Code Help?
      By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
    • CapnWalleye
      2016 Cub Cadet 500 runs rough
      By CapnWalleye
      Just picked up a Cub Cadet 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • CapnWalleye
      2016 Hisun 500 runs rough no power
      By CapnWalleye
      Just picked up a Hisun 500 that had shift issues (corroded fan gear) which I fixed. It also didn't seem to be running smoothly then all of a sudden it got worse. It seems to miss on both idle and when pushing the gas pedal to the floor and doesn't seem to be running at full power. I've been working with a local person who is walking me through some steps, but I'd like some input from this group as well. What I've done:
      - drained the fuel tank and replaced it with 93 octane fuel and added heet to help with any water problems.
      - replaced the fuel injector.
      - disconnected the battery (several times) to allow the module to reset.
      - set the valve clearance, both intake and exhaust, within specs ... intake was tight but exhaust seemed fine.
      - replaced the battery.
      - replaced the O2 sensor.
      Nothing has helped. Not sure what the next steps are, but would appreciate any expertise that can be offered here.
       
    • Bobbers
      Axis 500 parts
      By Bobbers
      My wife accidentally ran the Axis 500 into a fence and tore the front end up (broke her arm too). Just wondering where the best place to get front end parts? I know she busted the knuckle but haven’t jacked it up yet. Thanks guys for any help!
    • Homeowner A
      Code Reader for Delphi MT05 Coleman UTV 400 Hisun
      By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...