Quantcast
Jump to content


2015 Kymco 450I Transmission issues

Jason Larson

By Jason Larson
in Kymco UTV SxS Forum

 Share

Recommended Posts

Jason Larson Newbie

Jason Larson

Posted
Posted

I have a 2015 kymco 450I side by side with only 800 miles. I use it to plow snow and pull a manure spreader. Yes in low.  Last night it started making a loud chatter in the engine area and shut off. Couldn't change the gear selector unless it was while turning the ignition. Pulled the belt/clutch cover off and everything was in ok shape. Took the whole assembly off and it still chatters. Looks like the splined rod towards the rear of the engine is starting and stopping in its own and that's where that noise is coming from.  Is that part of the clutch and do I need to pull that too???  Don't know how deep to dig. And where to get these parts.

  • Alex changed the title to 2015 Kymco 450I Transmission issues
  • 3 months later...
Demotrucker Newbie

Demotrucker

Posted
Posted
On 1/18/2022 at 7:18 PM, Jason Larson said:

I have a 2015 kymco 450I side by side with only 800 miles. I use it to plow snow and pull a manure spreader. Yes in low.  Last night it started making a loud chatter in the engine area and shut off. Couldn't change the gear selector unless it was while turning the ignition. Pulled the belt/clutch cover off and everything was in ok shape. Took the whole assembly off and it still chatters. Looks like the splined rod towards the rear of the engine is starting and stopping in its own and that's where that noise is coming from.  Is that part of the clutch and do I need to pull that too???  Don't know how deep to dig. And where to get these parts.

Hi guys. Update on the Kymco issue. After getting zero help from the dealer i was able to figure out through pictures that this machine crossed with a 2015 Artic cat 450 snow mobile. Ebay had the parts. Fit perfect.  Clutch was worn down pretty good. Probably from pulling heavy stuff. Hope this helps anyone with this problem. 

On 1/18/2022 at 7:18 PM, Jason Larson said:

I have a 2015 kymco 450I side by side with only 800 miles. I use it to plow snow and pull a manure spreader. Yes in low.  Last night it started making a loud chatter in the engine area and shut off. Couldn't change the gear selector unless it was while turning the ignition. Pulled the belt/clutch cover off and everything was in ok shape. Took the whole assembly off and it still chatters. Looks like the splined rod towards the rear of the engine is starting and stopping in its own and that's where that noise is coming from.  Is that part of the clutch and do I need to pull that too???  Don't know how deep to dig. And where to get these parts.

 

  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • CSM_Retired
      Making Kioti K9 2400 Quieter Ideas
      By CSM_Retired
      Greetings All,
      I'm looking for the most effective way to quiet the noise inside the cab. The cab virtually sits atop the 24hp diesel engine. It's very loud and so I'm looking for ways to make inside the cab quieter.
       
    • Prepper
      2015 MSU-500 crank - no start
      By Prepper
      I'm working with a 2015 MSU-500.  Basic symptoms are it cranks well, but will not fire.  It has spark, and it has fuel spraying out of the injector (and spraying starting fluid into the throttle body and plug hole makes no difference).  It has compression.  I bought it not running, and no other information was available.  It has 775 miles on it and 127 hours.  It looks to be in very good shape.   Previous owner replaced fuel pump, ECU, coil, plug, and the fuse/relay box that mounts on the firewall, then gave up.
      My questions relate to cam/valve timing, considering the symptoms and diagnostics so far.  My thinking was the woodruff key sheared off and the crank spun, making it out of time.  My question is, by the pictures attached does anyone have an opinion as to the cam/valve timing being correct?  In the crankshaft picture you can see a timing mark visible.  In the camshaft picture I have arrows directed towards what I think are timing marks (which appear to be exactly 180 degrees from one another).  However, the long arrow in what appears to be bolt configuration in line with the piston/rod line.  Here is a puzzling note... in the position you see in the pictures... I have valve lash on both the intake and exhaust.  I think it's at TDC, given the visible crank timing mark and valve lash on both valves. 
      Any thoughts ?  Does this appear to be in proper valve time ?  Have I missed anything simple ?  Thanks in advance for your input.


    • Gorj
      Sector E1 Battery change out
      By Gorj
      I am going to replace the batteries in my E1. I am not interested in the high cost Lithium or the expensive 6 volt dry batteries.  I am considering four 12 volt deep charge marine batteries. I have a source for 810 amp units for about $100 each.  I have no worries about reprograming the charger because it went out a few years ago and I replaced it with generic golf cart charger. When I decide to do this, I'll keep you posted on the results.
    • Marie
      Wiring 2013 Hisun 800
      By Marie
      hello, i need help figuring out where all these wires go on this battery. I can't seem to find any pictures diagrams. As to what should or shouldn't be attached and where these two plugs go, that aren't plugged in. this was got as a project. would run then die and battery would have to be jumped off to start again stator has now been replaced but any help with this wiring would be appreciated. 
    • Marie
      2013 Hisun 800 Please Help Wiring
      By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...