Quantcast
Jump to content


Recommended Posts

Posted

My  problem is that when the temperature dips under 50 degrees, my Coleman 550 acts like the battery is dead and no electrical activity at all. The battery is at full charge. It only has 15 hours on it and the same thing happened last winter. Above 50 degrees, starts every time.  Very frustrating needless to say.  Anyone else experience this problem.  I bought it at Tractor supply and they are not a service center and don't know who works on them in the area.

Posted

So does it just not crank, or you don't have any electrical at all? (Lights, etc). Another thing, if you have a volt meter,  i would check the battery voltage with the key in the ON/RUN position and the START position. you may need helper to do that.

Posted
  • Same problem on my 2015 Sector 550. Full charge in battery.  No dash lights, no horn, no start, no nothing. I thoroughly cleaned every connection at the battery. The bat compartment looked new when I was done. SAME problem. NO change.
  • So I used a known GOOD fuse/relay unit. Same problem. NO change.
  • I even attempted a jump start from a running vehicle. Same problem. No change.
  • So I took it to a real Hisun mechanic who replaced the battery and it started right up. (I couldve sworn I did a LOAD test on my battery. I must've been wrong.
  • I NOW keep the UTV S/S on a trickle starter each time I park it.

This unit only had 300 miles on it when I bought it from a friend who didn't use it much. I'm learning as I go. Good luck.

  • Like 1
  • 1 month later...
Posted

Well thanks all for the advice---I put a  brand new battery in and still the same problem. The weather has gotten warmer and it will start above 50 degree's every time. Last weekend it drop into the 20's and it would not even get the dash to lights to come on . 2 days later, dash lights up and it started. Guess what temperature it was?  52 degrees. Craziest thing anyone has ever seen.  

Posted

I am a retired Diesel Mec.  First thing I did when I got my 2016 mule home was to take apart every connection I could find and added Dielectric Grease.  I took every ground I could find, cleaned the metal surface, coated with dielectric grease.  I have taken the mule through 3 ft of water with no issues.  Recommendation is check all powers and grounds.  Alot of issues come from bad grounds.  Also, check the power connection to the fuse block for corrosion and tightness.  Check the connection to the ignition switch for corrosion and the connections for tightness.  This is always my starting point with these UTV/ATV's.

  • 8 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Gorj
      I am going to replace the batteries in my E1. I am not interested in the high cost Lithium or the expensive 6 volt dry batteries.  I am considering four 12 volt deep charge marine batteries. I have a source for 810 amp units for about $100 each.  I have no worries about reprograming the charger because it went out a few years ago and I replaced it with generic golf cart charger. When I decide to do this, I'll keep you posted on the results.
    • By Homeowner A
      Is there a code reader available for the Coleman UTV 400?  I tried using the HUD ECU Hacker software and cables/adapters but no luck OBD to delphi 6 pin and KKL VAG as well as ELM327.  Will not connect.  I was able to get it to connect randomly a couple of times, but haven't been able to since.  I was able to clear and read the codes briefly.  I'm aware of the Tiny Scan 301 but it doesn't seem to be readily available.  There's a few out there but they are expensive.  
    • By Alien10
      I'm thinking of buying a snow blade for my Coleman Outfitter 550 (Hisun with Coleman stickers).
      Has anyone purchased a snow blade that can offer the make and model they bought and any comments, pros  cons etc.?
      Not 100% sure I'm going to buy, as the selection of blades for this model seems a bit thin on line. 
      Thoughts and comments welcomed.
      Thanks in advance.
    • By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • By SteveS
      While driving the MSU 800, it runs good but it lately it will not go over 20 MPH. The side by side will hesitate when it reaches 21 MPH, but it will run good under 20 MPH. What is the issue?
×
×
  • Create New...