Axis 500 / sound like rocks rattling from underneath
-
Similar Topics
-
By didgeridoo
Hello, All! I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth. I haven't torn anything apart yet (to diagram), so I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
-
By dman66
My buddy has a ut400 that the forward gear keeps popping out of gear. She only has like 400 miles on the odometer .the shift cable has been adjusted and the shift lever has been updated / modified. All other gears are good. Is there an internal detent cam or something that wears out or shift fork that can be replaced ? Or is there some other magic that I can perform ? Looks like the engine needs to be split.
-
By Homeowner A
Have a Coleman UTV 400 that cranks, runs, drives well until it gets warm and is put under load. Light throttle or full throttle it doesn't bog, but it will cut out mid throttle if you move the pedal quicker than it seems to like for example when you're getting ready to go up a hill, but if you immediately floor it, it will do just fine and not cut out. It's random if and when it's going to do it, but is consistent in that it happens only when hot/full operating temperature. I've replaced the injector twice, same with the spark plug and tried different heat ranges (NGK 7,8 and 8 iridium), replaced the fuel pump, adjusted the valves, checked air filter which is like new, changed the oil, replaced the fuel filter. No check engine light. I don't have a code reader for this. Initially I thought it might have a head or head gasket issue as when I got it, the oil was over full, very runny like water milky and it was smoking. I've changed the oil since then twice to clear and clean everything out, and it seems to be good. Coolant stays the same level and so does oil with no changes in consistency or need for adding more. Had I think 7-9 miles when I got it and now has about 77. What should I try or consider next?
-
By D MAYNARD
I have an Axis 500 4x4 UTV that I was given. It looks like an almost new machine with 39 hrs on it however it was apparently under water from the hurricane . I have no spark at the plug. I have replaced the plug, the plug wire, & the stator so far. Can anyone advise me of what i need to check and or replace to get this thing running? Any advise would be greatly appreciated.
Thank You,
D Maynard
-
-
By CRV
I’m need a couple parts. Diff. Lock Actuator mainly. But I would like to find a donor that maybe has bad motor or something along those lines.
if anyone has or knows of anything please holler at me
thanks Randy
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.