Quantcast
Jump to content


2018 Massimo msu500 No Start

Redneckguy

By Redneckguy
in Massimo UTV SxS Forum

 Share

Recommended Posts

Redneckguy Newbie

Redneckguy

Posted
Posted

My  msu500 has around 200 hours on it. I started it last week put it in low and made it about 6 feet. there was a pop and dead engine. Tried starting it again and it spun really fast and free. Well I started at the top tearing it down and what I’m seeing is the timing gear broke. Everything looks good other than the timing gear and I’m missing two pieces that now of course I have to tear the whole engine down to find lol. Has anyone had this happen? This thing has been a colossal piece of garbage since I’ve owned it. My dad bought it brand new and I got it with around 20 hours on it.

  • Alex changed the title to 2018 Massimo msu500 No Start
  • 3 months later...
motojoe Explorer

motojoe

Posted
Posted

If the timing gear broke that is on the camshaft there is no need to take apart the entire engine.  Take the Stator cover off and the flywheel, take off the timing chain adjuster off, put a new chain (if you want) and install a new camshaft and gear.  should only take a few hours not a bad job at all.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • mark walkom
      sector e1 regen has stopped (mostly) working
      By mark walkom
      the regen braking on my e1 has stopped working unless (for eg) I am going down a hill in low and it's slowing things down to stick to the 10kph limit. when I drive and take my foot off the accelerator it's not initiating the regen to slow things down and instead just coasts at whatever speed it is at, or speeds up as the regen is not limiting it. the brake lights work, so it's probably not a fault with the sensor on the brake pedal
       
      hoping someone else might be able to provide some suggestions on things to check, as the mob that I bought it off seem to have gone silent on me
    • Reynolds Rocket
      2017 Intimidator XD4 800 Check Engine
      By Reynolds Rocket
      I have a 2017 Intimidator XD4 800cc 4x4.  It will run great and then it's like it goes into safe mode and only runs on 1 cylinder.  It's not fouling out the plug when it happens.  Some times when I stop and restart it, it works fine.  First I thought it was a spark issue, then a fuel issue, but I feel like it's a short in the wiring some place. 
    • lmarkie
      Bulldog BD700 Engine Swap
      By lmarkie
      I swapped out the Subaru motor for a Predator 670cc. If I remove the heat shield around the muffler, The stock muffler sits in there just fine with 1" to spare.
      Only problem is the exhaust exit is toward the back seat instead of out the back.
      Do you all think that the stock exhaust would be okay (just as effective) if cut a hole and welded a pipe on the reversed (opposite) end? Of course, plug the old exit end. Other option I thought of was to roll a tube 180° with a 7" center line radius and finish extention of 12" or so.
      Any thoughts?
    • redneckred
      2012 Bennche 700X Engine code
      By redneckred
      Can anyone tell me how to get the engine codes to display on a 2012 Bennche Bighorn 700X?  I played with the gauges once and lucked up on this but can't remember what I did.  Will the codes automatically display if there is a code or do you have to cycle through the display?
    • Jeff S
      Stuck in LOW
      By Jeff S
      How to fix newer 800SX that gets stuck in LOW

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...