Quantcast
Jump to content


Seriously considering buying 2022 Axis 700 from Lowes… any regrets from current owners?


Go to solution Solved by Robert Scott,

Recommended Posts

Posted

So far so good. 23hours on the engine and all is well. No issues so far. I burn ethanol free gas with 94+ octane. Used the winch for the first time yesterday to pull a huge pine that had pinched my chainsaw; winch performed flawlessly.

  • 2 months later...
Posted
On 2/25/2022 at 6:54 AM, TapBoss said:

Just looked at the Lowes add for that, pretty much looks like an  MSU 500/700 that Hisun made for Massimo back then.  Take a good look at the badging on parts to see who it's actually made by, my guess is it's still Hisun.

I purchased one from Lowes. Axis 700.

it is made by HiSun in Texas and are rebadged with several names. Got  it in Feb  of 22’ and used mainly for Hunting property maintenance and  cruising around. Have had only one issue so far. Voltage regulator went out and local authorized dealer repaired it under warranty. 
For what comes with it (winch, windshield, etc.) the price is easy on your wallet. Will it last, is yet to be seen.  5 k more and a Polaris or Honda  could be yours, but that’s half the price of another HiSun  unit. 
Be Safe …

 

 

Posted
On 2/26/2022 at 11:30 PM, scott ryan said:

I picked up the Axis 750 quad cab a little under a year ago. Put about 40 hours on it.  Runs way better after break in adjustment and fluid changes, 20 hrs. Only issue was a $20 broken air/oil separator.  Helps to be handy with maintenance cause service centers are scarce around me.  If you purchase, inspect everything before you drive off. Others have had bad experiences in my area. I'm completely satisfied with mine. It will go anywhere.

I'm due for my break-in service with just over 50 miles on my Axis 500.  Which fluid changes did you perform (in addition to the engine oil and filter change)?  Local UTV shop is telling me that all of the fluid needs to be changed, from the final drive fluid to the differential fluid.  The owner's manual just talks about doing the oil change and filter change after the initial break-in period.

Posted
2 hours ago, Joe Breaux said:

50 miles is not the break-in period.. My manual says burn 3 tanks of gas to break-in.. 

For the Axis 500 it is, it says so in the owner's manual.  After the first 50 hours, it's then every 500 hours between oil changes and I plan to use full synthetic.

Posted
32 minutes ago, Shannon Watts said:

 

you wrote 50 MILES ....

 

11 hours ago, Shannon Watts said:

I'm due for my break-in service with just over 50 miles on my Axis 50 miles.  

not 50 hours ... BIG difference 

Posted
39 minutes ago, Shannon Watts said:

For the Axis 500 it is, it says so in the owner's manual.  After the first 50 hours, it's then every 500 hours between oil changes and I plan to use full synthetic.

 

4 minutes ago, Joe Breaux said:

you wrote 50 MILES ....

 

not 50 hours ... BIG difference 

My bad, it's 50 miles or 10 hours, whichever comes first.  

Screenshot 2022-06-28 202318.jpg

  • Thanks 1
Posted

So to Jones’s point the 10HR /or 50 MILE interval is what should happen. So says my 500/700 Axis Manual
FYI.  I had a charging problem. I did a voltage test with a Voltage Meter while running and it sat at 12.5. Not good. 
Please make sure you register your unit on the HiSun site. I had to call because my Lowes did not do all that the registration  section on the HiSun site said they should have. 
I took it to the vendor that is Authorized to work on the unit and they verified the battery was good .  After a weeks stay they called and said that the Voltage Regulator was bad and that it will be a few days.  I was at 16 hrs and as a good faith gester and convince  to me I asked if they would change the oil and filtered and lube the beast.   Figured warranty wouldn’t pay much and an oil change would put a few bucks toward the labor . 
Service told me that the manufacturer had NOT responded to the warranty claim and that I would be able to only pay for the OC and Lube and if Warranty didn’t cover my repairs that they would call and be asking for additional payment.   (To the tune of(225.00). 😳
The synthetic blend 10-W40  and filter change and lube was 96.67.     Without a kiss or a Veteran’s Discount.
Overall still glad I got the unit in FEB of 22 and use it around the house and for Hunting property maint. and eviction of a harvest.    
Check out You Tube Site    Caseymaples19xx   He has good content and shred his experience with a Axis 700

 

Posted
2 minutes ago, Buss said:

So to Jones’s point the 10HR /or 50 MILE interval is what should happen. So says my 500/700 Axis Manual. 
FYI.  I had a charging problem. I did a voltage test with a Voltage Meter while running and it sat at 12.5. Not good. 
Please make sure you register your unit on the HiSun site. I had to call because my Lowes did not do all that the registration  section on the HiSun site said they should have. 
I took it to the vendor that is Authorized to work on the unit and they verified the battery was good .  After a weeks stay they called and said that the Voltage Regulator was bad and that it will be a few days.  I was at 16 hrs and as a good faith gester and convenience   to me I asked if they would change the oil and filter and lube the beast.   Figured warranty wouldn’t pay much and an oil change would put a few bucks toward the labor . 
Service told me that the manufacturer had NOT responded to the warranty claim and that I would be able to only pay for the OC and Lube and if Warranty didn’t cover my repairs that they would call and be asking for additional payment.   (To the tune of(225.00). 😳
The synthetic blend 10-W40  and filter change and lube was 96.67.     Without a kiss or a Veteran’s Discount.
Overall, still glad I got the unit in FEB of 22 and use it around the house and for Hunting property maint. and evacuation of a harvest.    
Check out You Tube Site  Caseymaples19xx   He has good content and his experience with a Axis 700

 

 

Posted
16 hours ago, Shannon Watts said:

I'm due for my break-in service with just over 50 miles on my Axis 500.  Which fluid changes did you perform (in addition to the engine oil and filter change)?  Local UTV shop is telling me that all of the fluid needs to be changed, from the final drive fluid to the differential fluid.  The owner's manual just talks about doing the oil change and filter change after the initial break-in period.

I did the final drive and diff fluid as well. Neither were difficult. Royal Purple 75w90.

Posted
7 hours ago, scott ryan said:

I did the final drive and diff fluid as well. Neither were difficult. Royal Purple 75w90.

Looks like both take less than 1/3 of a quart.  Did you just buy 1 qt jug for both the final drive and differential or did you end up having to buy 2 x 1qt jugs after draining both fluids?

Posted
3 hours ago, Shannon Watts said:

Looks like both take less than 1/3 of a quart.  Did you just buy 1 qt jug for both the final drive and differential or did you end up having to buy 2 x 1qt jugs after draining both fluids?

I buy 2 of everything, just need one tho. I go by the old philosophy of 1 is none and 2 is 1.  Never know when the supply chain will crash or prices will spike. Good luck!

  • 3 weeks later...
Posted

Glad I found this thread. I'm considering the Axis 700, too. I've been rebuilding this 2009 for over a year and there are so many new parts in it it's practically new. And practically all Yamaha parts. :) But I might just sell it and spring for a new Axis 700. BUT Lowe's seems to be always out of stock. Does anyone know if there's a long backorder wait time on these?

 

20220615_145619.jpg

Posted
12 hours ago, Buss said:

Lowes in Mechanicsville,VA has probably 7or 8 sitting out front.

Well, that's good. At least they're still selling them somewhere. Thanks.

 

Posted
14 hours ago, RickinMT said:

Glad I found this thread. I'm considering the Axis 700, too. I've been rebuilding this 2009 for over a year and there are so many new parts in it it's practically new. And practically all Yamaha parts. :) But I might just sell it and spring for a new Axis 700. BUT Lowe's seems to be always out of stock. Does anyone know if there's a long backorder wait time on these?

 

20220615_145619.jpg

They are a decent machine after you swap out the junk parts for OEM Yamaha pieces . Problem is, I dont want to go thru that nightmare again.. My next will be Honda or Kawasaki. The guys I ride with never have issues. they are bulletproof 

  • Like 1
  • 1 year later...
Posted (edited)

Hey all.  Just thought I'd weigh in with our pretty much horrible experience with a new Axis 700 purchased last May 2023 from Lowes in Winchester, VA.  Brought it home, put about 10 hours on it and it won't hold a charge.  LOOOOONG story, the mobile tech has been out 4 times, replaced the battery, voltage regulator twice.  I told him in February I thought (after doing a bit of research) that it was the stator, since if kept on the trickle charger it reads 100% charged, run it 15 minutes and it's down to 40%-that means the stator is not charging the battery while it's running.  Anyway, last time he came out the part that he was supposed to change out was shipped in too small a package and was bent and unusable.  I have about a 10 page email chain to 6 different folks at Hisun in TX begging for some resolution.  They ignore my calls, emails, voice mails, etc.  Needless to say, we are really frustrated with the vehicle, the company, the mechanic; pretty much everything to do with this worthless POS.    It is truly ridiculous to spend $10K on something that is now sitting in our garage torn apart waiting for the worthless mechanic once again.

UPDATE:  Now the tech is scheduled today for his, yes 6th visit.  This time, in addition to replacing the stator, it now has a cracked water pump that needs to be replaced.  This on a vehicle that still has 10 use hours on it.  (It has an additional 5 from running during repair visits).  The support from Lowes and Hisun has been nothing short of abysmal.  

Edited by GigiH
update
Posted

I run screaming at the mere mention of the word HISUN....I had a nightmare of problems with mine  ,beginning on it's first day.and got zero help from Massimo in TX or HISUN in China

  • 1 month later...
Posted

Don't do it had problems from day one 2021 axis 700 UTV starter clutch gear went I don't even think there's 30 miles on it it's been sitting cannot find the part anywhere ordered one from eBay it was the wrong one don't do it you can't get the parts for it anymore

  • Like 1
Posted

I really believe that the design of the Hisun 500/700 is very good but the people building them are very bad.  They apparently  know nothing (or just don't care) about quality control and customer support.  If a good company were to buy them out and fire everyone that ever had anything to do with building them and replace with good engineers, QC, customer support people, they could corner the market.  As it is now don't buy one unless you are fully ready to maintain it on your own because you will have problems.

  • Like 2
Posted
10 hours ago, klm said:

I really believe that the design of the Hisun 500/700 is very good but the people building them are very bad.  They apparently  know nothing (or just don't care) about quality control and customer support.  If a good company were to buy them out and fire everyone that ever had anything to do with building them and replace with good engineers, QC, customer support people, they could corner the market.  As it is now don't buy one unless you are fully ready to maintain it on your own because you will have problems.

The engine is a 95% clone of YAMAHA Rhino but built with lesser quality parts and assembly..I Have replaced broken defective parts with YAMAHA Parts on my 500 Hisun engine. It has become acceptable SXS now. Mine broke on its first day in its first mile. Neither Hisun or Massimo would back warranty. 6 trips to shop all paid out of pocket..I discourage anyone from buying anything made by Hisun.☠

  • Like 2
  • 3 months later...
Posted
On 2/28/2022 at 2:38 PM, Joe Breaux said:

I bought a MSU 500  Massimo /HISUN product from Tractor Supply. in 2018   .. In the shop 6 times in first year for overheating, cracked head, head gaskets , waterpump, etc...... ZERO WARRANTY REIMBURSEMENT from company...  It broke on  its first use on its first day!!    RUN, dont walk away from any HISUN UTV.. They are junk .. You have been warned. 

Yup. Ditto. 

  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By NC4wd
      Has anyone found a lift kit that fits an Axis 500? Mine is a 2021.
    • By Greg Kilgore
      Last year bought a small universal coolant style cab heater. Well I installed it today. Thanks to another member, RangeRider45, and his install
       
      That told in his post the size fitting he used. I got the same fittings plus a few others. And all went kinda smooth. Took a few minutes to get air purged from coolant system. Should have parked on hill with front up in the air. But would have had a hard time working on it.
      I had a variable power switch connected to an overhead cab fan. Never really used the fan that much. And I have to remove the fan to put on my cab enclosure anyway. So I repurposed the switch to supply power for the heater. The heater has 2 12-volt DC computer fans that are rated for 1.8 amps each. So it's not going to be a big drain on the weak charging system. And with the switch I've got great control over the speed of the fans.
      If anyone is interested the radiator hoses are 7/8 inch. I reworked the temperature sending unit (moved it closer to radiator) to make room for all the extra plumbing I did to get the heater to work the way I wanted. 
      Plumbing parts list.
      10-15 worm water clamps. 3/4 to 1 1/4 inch size.
      2 1" x 3/4" x 1" PEX Tee
      1 3/4" PEX ball valve
      1 1" PEX ball valve
      5/8" heater hose. I got 6' and probably have 4' left over.
      I used the radiator house I cut out to use as splices between the PEX fittings. The PEX fittings are not true to their dimensions that are stated on the package. So they fit the 5/8" and 7/8" very nicely.
      They way I have it plumbed is from radiation out side. A tee, then the 1" ball valve, then a Tee. Coming off the Tees are the hoses going to the heater core. There is a 3/4" ball valve on one of the Tees. The ball valves are used to bypass the heater core in the summer. Or direct the hot coolant through the heater core in winter. The temperature sending unit tells me how hot the coolant is. And if anything is getting too hot. The dash also has an idiot light that comes on if the head gets too hot. But doesn't do anything if the radiator gets too hot. There is a temp sensor on the radiator that controls the electrical fan. But if the coolant isn't circulating. That switch never sends a signal to turn on the fan. But enough talking/rambling. Everyone wants to see pics. The only thing I need to change is the orientation of the handle on the 1" ball valve. I have 2" or more clearance between the handle and the tire when cut hard right. But I still don't like it. And instead of taking the valve out and rotating 180°. I'm just going to take the nut off and rotate the handle 180°. Think I need to make a locking mechanism to lock the handles in place so they don't vibrate closed when the machine is moving.
      The temperature sending unit and housing. Size 22 mm. Aluminum from Amazon.

      Upper Tee the lower Tee is identical. Can also see the handle of the 3/4" ball valve on the 5/8" hose going to the heater.

      The 1" ball valve. Goes between the 2 Tees

      Wide view of the plumbing.

      The heater installed in the sxs. The 3 black hoses are just hanging there. Zip ties to the heater but not attached to any thing. Will probably just direct 2 toward the wife's feet. And 1 toward mine. Or what ever is need as the heat is needed on rides. The black hose in passenger floorboard is some 1" hose that is not needed. Don't know what I'll do with it.

       
      I think if I was going to do it again. I'd put some Indian Head gasket dressing or silicone on the 1" side of the PEX fittings. And I may still do that. But I really hate the ideal of introducing air back in the coolant system.
       
      Any questions just ask. It may take a while to answer. But I'll try.
      Ya be good and stay warm over the next few months 
       
      Kilgore.
    • By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
    • By mac66
      I bought a used 2021 Axis 500 last April.  Low mileage and got it for considerably less than what they go for new.
      The first thing I did was change the oil/fluids and also put a new drive belt on it.  The only other thing I did to it was add a rear vinyl window that zips open and rolls up to keep the weather off.
      I used it on my 52 acre property to check trail cameras, service the food plots, haul fertilizer, seed etc etc. It's has a good size bed and is not too big or small.  It has worked well as a utility vehicle. 
      Other than using on the trails working around the property I haven't used it much off road...at least until last weekend when I went on 74 mile group ride around the county. In my state it's legal to ride on any road that's not a state or federal highway. The group started in town, rode about 30 miles on back roads to the state ORV trail system. Then did about 20 miles on the trails and then headed back via back roads to town.   
      It had rained for 2 days straight prior, so the trails were one mud hole after another.  It was very challenging.
      The good...
      -It worked fine, never had any kind of issue with it since I bought it.
      -It kept up with more expensive machines on the trails. I was the only one with a CCC (Cheap Chinese Crap) machine.
      -Fairly comfortable to drive.
      -The roof, windshield and rear window kept most of the rain off when it started raining in the afternoon.
      -Okay, I cheated. I peeled off the AXIS 500 stickers on each side. Everybody in the group assumed I had a Rhino. They didn't ask, I didn't tell.
      The not so good...
      -The horsepower rating on the 500-cc engine is 24 hp but it seemed underpowered. While I could go about 35 mph with the pedal to the metal on pavement and hard packed dirt roads the best I could do on loose packed roads was 27 mph. I had trouble keeping up with the others in the group.  It also bogs down on inclines in high gear.  On the other hand, in low gear and 4wd I didn't have any problems going through mud or sand or up hills.
      -It is LOUD! Had to wear shooting earmuffs to keep my ears from ringing while riding. Going to have to address that.
      Overall Impression...
      I was impressed with it on the trails, and it is a good utility vehicle for working around the property. Considering what I paid for it I am very happy with its performance.
    • By TPlummer
      We recently purchased the Axis x550. Fueled it with 93 fuel and drove one time around the farm and the 02 fault error appeared. Any ideas? 
×
×
  • Create New...