Quantcast
Jump to content


Recommended Posts

Posted

Just bought a brand new Hisun HS 750 Crew. Dealership started it up and drove it on to my trailer. Got it home and it won't start. Battery clicks over but nothing else happens. Tried jumping battery but no luck there.  Dealership is closed through the weekend and not sure what else to try. 

Posted
On 3/4/2022 at 12:08 PM, Joe Breaux said:

apply the brakes , then start 

 

On 3/4/2022 at 12:08 PM, Joe Breaux said:

apply the brakes , then start 

 

On 2/27/2022 at 2:01 PM, DieselSports said:

Just bought a brand new Hisun HS 750 Crew. Dealership started it up and drove it on to my trailer. Got it home and it won't start. Battery clicks over but nothing else happens. Tried jumping battery but no luck there. 

Double check battery cables and battery posts, clean both then tighten battery bolts. Check fuses with a multimeter. Also check fuse block for starter, if it clicks when turning key to start, there may be a short in it. Tap it with pliers or small hammer. If it still clicks try shorting across posts on fuse block with a screw driver. If all fails take it back to dealer when it reopens. Good Luck!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Similar Topics

    • By hisun junk
      As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

    • By Frank in MI
      Thanks for accepting me!
      Haven't got a side by side yet, but have been shopping.   
      Any advice welcome & I am on a limited budget, so haven't decided yet on new or used.
       
    • By Poppateets
      I just purchased a used 2023 Massimo warrior UTV SxS 1000mx with 600 miles on it. I didn't even get a full day of riding and the driver's side rear axle broke. I'm pretty sure it was already going bad because we would hear a noise once in a while. I'm wondering if anyone else has had problems with theirs. Also looking for places to buy accessories.
    • By Justine
      I've had a Hisun Vector E1 for just a bit longer than is required for me to do some maintenance. While it's well-overdue, it only drives 1.5km a few times each week on a fairly decent gravel road (to the letterbox), and it has worked really well right from the get-go.
      Looking at the manual it states that I need to use SAE80 API GL-4 Hypoid Gear Oil for the Main gear Case, and SAE80 API GL-5 Hypoid Gear Oil for the Front gear Case - unfortunately i can't find either of those online here in Australia. Plenty of options that look close, but, as someone who has never driven any vehicle before, I want to use the right thing and it's a tad confusing.
      My question: Since there are no oils that are bang on SAE80 (they all seem to cover a range) would Liqui Moly Hypoid GL4 Gear Oil 80W-90  & Motorex Hypoid GL-5 Gear Oil 80W90 - be ok to use? (Or any other suggestions of what I might be able to purchase online in Australia) And would I have to drain out any existing oil from both gear cases?
      This is a whole new world for me and  being able to find exactly what is specified in the manual hasn't made this easy!
    • By se3388
      Hopefully someone else will buy a UT10X and join in.
       
      Steve.............
×
×
  • Create New...